www.vishay.com

61

CS206

Vishay Dale

Document Number: 31519

Revision 10-Sep-04

For Technical Questions, contact: ff2aresistors@vishay.com

CONDITION

Subject to 5 cycles from - 65°C to + 125°C.

2.5 x rated working voltage for 5 seconds at + 25°C.

Cycle from + 25°C to + 65°C to + 25°C over 8 hours at 90 - 98% relative humidity,

with 10% of rated power applied, for 20 cycles. Stop cycling after an even number

of cycles and stabilize networks at high humidity for 1 to 4 hours. Condition

networks at -10°C for 3 hours, then return to temperature cycling. On completion of

cycling condition networks at + 25°C at 50% r.h. for 22 to 24 hours.

Immerse pins in melted solder to the lead standoffs at + 350°C for 3 seconds max.

18 shocks of 100 G and 6 ms.

12 cycles varied logarithmically from 10Hz to 2000Hz to 10Hz over 20 minutes.

1000 hours at + 70°C, rated power applied 1.5 hours “ON, 0.5 hour “OFF”.

Immerse and scrub samples with isopropyl alcohol, trichlorethylene and Freon TMC.

Immerse leads in 60/40 tin-lead solder using R flux at + 245°C for 5 seconds

maximum.

Withstand 2.2 kg pull 1 minute.

100 V applied between case and terminals tied together.

TEST

Thermal Shock

Short Time Overload

Moisture Resistance

Resistance to Soldering Heat

Mechanical Shock

Vibration

Load Life

Resistance to Solvents

Solderability

Terminal Strength

Case Insulation Resistance

PERFORMANCE

MAX.

(Typical Test Lots)

± 0.5% ∆R

± 0.25% ∆R

± 0.5% ∆R

± 0.25% ∆R

± 0.25% ∆R

± 0.25% ∆R

± 1.0% ∆R

Marking remains legible

Minimum 95% solder

coverage

± 0.25% ∆R

IR = 10,000 Megohm

minimum

Pin #1 is extreme left-hand terminal on side with marking.

DIMENSIONS in inches [millimeters]

NUMBER

OF PINS

4 pin

5 pin

6 pin

7 pin

8 pin

9 pin

10 pin

11 pin

12 pin

13 pin

14 pin

15 pin

16 pin

17 pin

18 pin

L

MAXIMUM

0.400 [10.16]

0.500 [12.70]

0.600 [15.24]

0.700 [17.78]

0.800 [20.32]

0.900 [22.86]

1.000 [25.40]

1.100 [27.94]

1.200 [30.48]

1.300 [33.02]

1.400 [35.56]

1.500 [38.10]

1.600 [40.64]

1.700 [43.18]

1.800 [45.72]

0.100

Non-Cumulative

at Point of Egress

H

Max.

L

Max.

0.020

[0.508]

0.050 [1.27]

0.135 [3.43] Max.

0

Ref.

Seating Plane

for 0.040 [1.016] Ø Hole

0.085 [2.160] Typ.

0.050 [1.27] Typ.

0.135 + 0.015 - 0.010

[3.43 + 0.381 - 0.254]

0.010

[0.254]

H (Height) Maximum:

B = 0.250" [6.35] (Circuit E and M)

C = 0.350" [8.89] (Circuit T)

E = 0.325" [8.26] (Circuit A)

Derating

150

100

50

0

0

25

50

75

100

125

150

Ambient Temperature

Res/CapNetworks, ECL Terminators and Line Terminator

Flammability:

UL 94V-0.

Lead Material:

Phosphorus-bronze, solder plated.

Body Material:

Epoxy coated.

Solderability:

Per MIL-STD-202, Method 208E.

Part Marking:

Pin #1 identification, part number

(abbreviated as space allows),

Moisture Resistance:

Meets requirements of MIL-STD-

202, Method 106.

70

CL

MATERIAL SPECIFICATIONS