ST92F120JR9T datasheet(271/320 Pages) STMICROELECTRONICS

271 / 320 page

271/320

J1850 Byte Level Protocol Decoder (JBLPD)

J1850 BYTE LEVEL PROTOCOL DECODER (Cont’d)

JBLPD SYSTEM FREQUENCY SELECTION

R244- Read/Write

Reset Value: 0000 0000 (00h)

Bit 7 = 4X

Diagnostic Four Times Mode.

This bit is set when the J1850 clock rate is chosen

four times faster than the standard requests, to

force the BREAK symbol (nominally 300

µs long)

and the Transmitter Timeout Time (nominally 1

ms) at their nominal durations.

When the user want to use a 4 times faster J1850

clock rate, the new prescaler factor should be

stored in the FREQ[5:0] bits and the 4X bit must be

set with the same instruction. In the same way, to

exit from the mode, FREQ[5:0] and 4X bits must

be placed at the previous value with the same in-

struction.

0: Diagnostic Four Times Mode disabled

1: Diagnostic Four Times Mode enabled

Note: Setting this bit, the prescaler factor is not au-

tomatically divided by four. The user must adapt

the value stored in FREQ[5:0] bits by software.

Note: The customer should take care using this

mode when the MCU internal frequency is less

than 4MHz.

Bit 6 = Reserved.

Bit 5:0 = FREQ[5:0]

Internal Frequency Selectors.

These 6 bits must be programmed depending on

the internal frequency of the device. The formula

that must be used is the following one:

MCU Int. Freq.= 1MHz * (FREQ[5:0] + 1).

Note: To obtain a correct operation of the periph-

eral, the internal frequency of the MCU (INTCLK)

must be an integer multiple of 1MHz and the cor-

rect value must be written in the register. So an in-

ternal frequency less than 1MHz is not allowed.

Note: If the MCU internal clock frequency is lower

than 1MHz, the peripheral is not able to work cor-

rectly. If a frequency lower than 1MHz is used, the

user program must disable the peripheral.

Note: When the clock prescaler factor or the MCU

internal frequency is changed, the peripheral could

lose the synchronization with the J1850 bus.

JBLPD CONTROL REGISTER (CONTROL)

R245- Read/Write

Reset Value: 0100 0000 (40h)

The CONTROL register is an eight bit read/write

Reads of this register return the last written data.

Bit 7 = JE

JBLPD Enable.

The JBLPD block enable bit (JE) enables and dis-

ables the transmitter and receiver to the VPWO

and VPWI pins respectively. When the JBLPD pe-

ripheral is disabled the VPWO pin is in its passive

state and information coming in the VPWI pin is ig-

nored. When the JBLPD block is enabled, the

transmitter and receiver function normally. Note

that queued transmits are aborted when JE is

cleared. JE is cleared on reset, by software and

setting the JDIS bit.

0: The peripheral is disabled

1: The peripheral is enabled

Note: It is not possible to reset the JDIS bit and to

set the JE bit with the same instruction. The cor-

rect sequence is to first reset the JDIS bit and then

set the JE bit with another instruction.

FREQ5 FREQ4 FREQ3

FREQ2

FREQ1 FREQ0

JDIS

NFL

JDLY4 JDLY3 JDLY2 JDLY1 JDLY0

ST92F120JR9T データシート(PDF) 271 Page - STMicroelectronics

ST92F120JR9T データシート(HTML) 271 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード