STM32F413CG datasheet(137/207 Pages) STMICROELECTRONICS

137 / 207 page

DocID029162 Rev 2

137/207

STM32F413xG/H

Electrical characteristics

174

I2S interface characteristics

Unless otherwise specified, the parameters given in Table 67 for the I2S interface are

derived from tests performed under the ambient temperature, fPCLKx frequency and VDD

supply voltage conditions summarized in Table 16, with the following configuration:

•

Output speed is set to OSPEEDRy[1:0] = 10

•

Capacitive load C = 30 pF

•

Measurement points are done at CMOS levels: 0.5VDD

Refer to Section 6.3.16: I/O port characteristics for more details on the input/output alternate

function characteristics (CK, SD, WS).

Note:

Refer to the I2S section of RM0430 reference manual for more details on the sampling

frequency (FS).

fMCK, fCK, and DCK values reflect only the digital peripheral behavior. The values of these

parameters might be slightly impacted by the source clock precision. DCK depends mainly

on the value of ODD bit. The digital contribution leads to a minimum value of

(I2SDIV/(2*I2SDIV+ODD) and a maximum value of (I2SDIV+ODD)/(2*I2SDIV+ODD). FS

maximum value is supported for each mode/condition.

Table 67. I2S dynamic characteristics(1)

Symbol

Parameter

Conditions

Min

Max

Unit

fMCK

I2S Main clock output

256 * 8K 256 * Fs(2)

MHz

fCK

I2S clock frequency

Master data: 32 bits

64 * Fs

MHz

Slave data: 32 bits

64 * Fs

DCK

I2S clock frequency duty cycle Slave receiver

tv(WS)

WS valid time

Master mode

3.5

th(WS)

WS hold time

Master mode

1.5

tsu(WS)

WS setup time

Slave mode

2.5

th(WS)

WS hold time

Slave mode

0.5

tsu(SD_MR)

Data input setup time

Master receiver

tsu(SD_SR)

Slave receiver

2.5

th(SD_MR)

Data input hold time

Master receiver

th(SD_SR)

Slave receiver

1.5

tv(SD_ST)

Data output valid time

Slave transmitter (after enable edge)

tv(SD_MT)

Master transmitter (after enable edge)

th(SD_ST)

Data output hold time

Slave transmitter (after enable edge)

3.5

th(SD_MT)

Master transmitter (after enable edge)

1.5

1. Guaranteed by characterization.

2. The maximum value of 256xFs is 50 MHz (APB1 maximum frequency).

STM32F413CG データシート(PDF) 137 Page - STMicroelectronics

STM32F413CG データシート(HTML) 137 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード