LTC2230 datasheet(18/28 Pages) LINER

18 / 28 page

LTC2230/LTC2231

22301p

60) may be used to provide the common mode bias level.

VCM can be tied directly to the center tap of a transformer

to set the DC input level or as a reference level to an op amp

differential driver circuit. The VCM pin must be bypassed to

ground close to the ADC with a 2.2µF or greater capacitor.

Input Drive Impedance

As with all high performance, high speed ADCs, the

dynamic performance of the LTC2230/LTC2231 can be

influenced by the input drive circuitry, particularly the

second and third harmonics. Source impedance and input

reactance can influence SFDR. At the falling edge of ENC,

the sample-and-hold circuit will connect the 1.6pF sam-

pling capacitor to the input pin and start the sampling

period. The sampling period ends when ENC rises, holding

the sampled input on the sampling capacitor. Ideally the

input circuitry should be fast enough to fully charge

the sampling capacitor during the sampling period

1/(2FENCODE); however, this is not always possible and the

incomplete settling may degrade the SFDR. The sampling

glitch has been designed to be as linear as possible to

minimize the effects of incomplete settling.

For the best performance, it is recommended to have a

source impedance of 100Ω or less for each input. The

source impedance should be matched for the differential

inputs. Poor matching will result in higher even order

harmonics, especially the second.

Input Drive Circuits

Figure 3 shows the LTC2230/LTC2231 being driven by an

RF transformer with a center tapped secondary. The

secondary center tap is DC biased with VCM, setting the

ADC input signal at its optimum DC level. Figure 3 shows

a 1:1 turns ratio transformer. Other turns ratios can be

used if the source impedance seen by the ADC does not

exceed 100Ω for each ADC input. A disadvantage of using

a transformer is the loss of low frequency response. Most

small RF transformers have poor performance at frequen-

cies below 1MHz.

Figure 4 demonstrates the use of a differential amplifier to

convert a single ended input signal into a differential input

signal. The advantage of this method is that it provides low

frequency input response; however, the limited gain band-

width of most op amps will limit the SFDR at high input

frequencies.

Figure 5 shows a single-ended input circuit. The imped-

ance seen by the analog inputs should be matched. This

circuit is not recommended if low distortion is required.

The 25Ω resistors and 12pF capacitor on the analog inputs

serve two purposes: isolating the drive circuitry from the

sample-and-hold charging glitches and limiting the

wideband noise at the converter input. For input frequen-

cies higher than 100MHz, the capacitor may need to be

decreased to prevent excessive signal loss.

Figure 3. Single-Ended to Differential Conversion

Using a Transformer

Figure 4. Differential Drive with an Amplifier

APPLICATIO S I FOR ATIO

Figure 5. Single-Ended Drive

25Ω

0.1µF

AIN

–

AIN

–

12pF

2.2µF

VCM

LTC2230/

LTC2231

ANALOG

INPUT

0.1µFT1

1:1

T1 = MA/COM ETC1-1T

RESISTORS, CAPACITORS

ARE 0402 PACKAGE SIZE

22301 F03

25Ω

AIN

–

AIN

–

12pF

2.2µF

VCM

LTC2230/

LTC2231

22301 F04

–

ANALOG

INPUT

HIGH SPEED

DIFFERENTIAL

AMPLIFIER

AMPLIFIER = LTC6600-20, AD8138, ETC.

25Ω

0.1µF

ANALOG

INPUT

VCM

AIN

–

AIN

–

10k

12pF

22301 F05

2.2µF

10k

25Ω

0.1µF

LTC2230/

LTC2231

LTC2230 データシート(PDF) 18 Page - Linear Technology

LTC2230 データシート(HTML) 18 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

データシートダウンロード

リンク URL

LTC2230 データシート(PDF) 18 Page - Linear Technology

LTC2230 データシート(HTML) 18 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

データシート ダウンロード

リンク URL

データシートダウンロード