LMV321TP datasheet(3/18 Pages) 3PEAK

3 / 18 page

LMV321TP/LMV358TP/LMV324TP

40μA, 1.27MHz, Micro-Power Rail-to-Rail I/O Op Amps

www.3peakic.com.cn

REV A.02

5V Electrical Characteristics

The

● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 27° C.

VSUPPLY = 5V, VCM = VOUT = VSUPPLY/2, RL = 100KΩ, CL =100pF

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

VOS

Input Offset Voltage

VCM = VSUPPLY/2

●

-3.5

± 0.1

+3.5

VOS TC

Input Offset Voltage Drift

0.6

μV/° C

Input Bias Current

1.0

IOS

Input Offset Current

1.0

Input Voltage Noise

f = 0.1Hz to 10Hz

5.6

μVP-P

Input Voltage Noise Density

f = 1kHz

f = 10kHz

nV/√Hz

RIN

Input Resistance

>100

GΩ

CIN

Input Capacitance

Differential

Common Mode

1.5

3.0

CMRR

Common Mode Rejection Ratio

VCM = 0.1V to 4.9V

●

110

VCM

Common-mode Input Voltage

Range

●

-0.1

5.1

PSRR

Power Supply Rejection Ratio

●

102

AVOL

Open-Loop Large Signal Gain

VOUT = 2.5V, RLOAD = 100kΩ

●

102

VOUT = 0.1V to 4.9V, RLOAD = 100kΩ

●

102

VOL

Output Swing from Supply Rail

RLOAD = 100kΩ

ISC

Output Short-Circuit Current

Sink or source current

Quiescent Current per Amplifier

●

μA

Phase Margin

RLOAD = 100kΩ, CLOAD = 100pF

Gain Margin

RLOAD = 100kΩ, CLOAD = 100pF

-15

GBWP

Gain-Bandwidth Product

f = 1kHz

1.27

MHz

Settling Time, 1.5V to 3.5V,

Unity Gain

Settling Time, 2.45V to 2.55V,

Unity Gain

0.1%

0.01%

0.1%

0.01%

2.3

2.8

0.33

0.38

μs

Slew Rate

AV = 1, VOUT = 1.5V to 3.5V, CLOAD =

100pF, RLOAD = 100kΩ

0.9

V/μs

FPBW

Full Power Bandwidth

2VP-P

140

kHz

THD+N

Total Harmonic Distortion and

Noise

f=1kHz, AV=1, RL=100kΩ, VOUT = 2VPP

f=10kHz, AV=1, RL=100kΩ, VOUT = 2VPP

-105

-90

Note: Stresses beyond those listed under Absolute

Maximum Ratings may cause permanent damage to

the device. Exposure to any Absolute Maximum Rating

condition for extended periods may affect device

reliability and lifetime.

The inputs are protected by ESD protection diodes to

each power supply. If the input extends more than

500mV beyond the power supply, the input current

should be limited to less than 10mA.

A heat sink may be required to keep the junction

temperature below the absolute maximum rating when

the output is shorted indefinitely.

Thermal resistance varies with the amount of PC

board metal connected to the package. The specified

values are for short traces connected to the leads.

Full power bandwidth is calculated from the slew rate

FPBW =

SR/π • VP-P.

LMV321TP データシート(PDF) 3 Page - 3PEAK INC.

LMV321TP データシート(HTML) 3 Page - 3PEAK INC.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

データシートダウンロード