V17

2

SPECIFICATIONS

All Specifications Typical At Nominal Line, Full Load, and 25℃ Unless Otherwise Noted

INPUT SPECIFICATIONS:

GENERAL SPECIFICATIONS:

Input Voltage Range ........……………....…........... 5V ........................... 4.5-9V

Efficiency ..............................................................…..……... See Table

12V .......................... 9-18V

Isolation Voltage ..........……………………....…..........…. 1500VDC min.

24V ........................ 18-36V

Isolation Resistance .........................…........................…. 10

48V ..………........... 36-75V

Isolation Capacitance ………………..……………………..…… 500pF typ.

Input Surge Voltage (100ms max.) ………….….… 5V …............... 15Vdc max.

Switching Frequency ......................….............……………... 100KHz min.

12V ................. 25Vdc max.

Operating Ambient Temperature …………………...

…

... -40℃ to +85℃

24V ................. 50Vdc max.

De-rating, Above 85℃ …………..……… Linearly to Zero power at 100℃

48V ............... 100Vdc max.

Case Temperature (note4) ………………………………….. 100℃ max.

Under Voltage Protection (note5):

Cooling ………………………………..…….…………. Natural Convection

5Vin Power Up …………………….....………..... 4.2Vdc max.

Storage Temperature …………………..….......……........ -55℃ to +125℃

Power Down …………………....……………. 3Vdc min.

Humidity .................................................. 95% RH max. Non condensing

12Vin Power Up ……….………………..……...... 7.3Vdc max.

MTBF ……MIL-HDBK-217F, GB, 25℃, Full Load ……… 2500Khrs typ.

Power Down ………………………..………. 5.8Vdc min.

Dimensions …………..… 0.86x0.36x0.44 inches(21.80x9.20x11.10 mm)

24Vin Power Up ………………………..……….... 15.5Vdc max.

Case Material ……………………………… Non-Conductive Black Plastic

Power Down …………………..……………. 12Vdc min.

Weight …….……………………………………….……………………... 4.8g

48Vin Power Up ………………………..………...... 31Vdc max.

NOTE:

Power Down ………………………..………. 24Vdc min.

1. For asymmetric loading both channels must be at 25% load or more.

Input Filter ………………………………………………..….………... Capacitive

2. Measured from high line to low line.

Remote on/off control (note6):

3. Measured from full load to 10% load.

Module Off (input idle current) ……..……… 1mA max.

4. Maximum case temperature under any operating condition should

OUTPUT SPECIFICATIONS:

not be exceeded 100℃.

Voltage Accuracy ............................................……….................. ±1.5% max.

5. Suffix “ N “ to the model with under voltage protection.

Voltage Balance(Dual) ………………………………….………….... ±1.0% max.

6. Suffix “ N “ Models: Module on …………. 0 to < 0.8VDC or open circuit

Cross regulation(Dual)(note1) .. Asymmetrical load 25%/100% ... ±5.0% max.

Module off ………..………..…………..4 to 15VDC

Transient Response: 25% Step Load Change

Other Models: Module on …….…. 0 to < 1.2VDC or open circuit

Error Band ……….………………….. ±6% Vout nominal

Module off………..………..……….. 5.5 to 15VDC

Recovery Time …………..……………….…….. < 500us

Ripple & Noise, 20MHz BW ……………..….……………..... 75mV pk-pk max.

Temperature Coefficient ....................……….......….............…..... ±0.03%/°C

Line Regulation (note2) .…….…………………..........................…. ±0.5% max.

Load Regulation (note3) ……..…....… Single …..........…............. ±0.5% max.

Dual …...……………….... ±1.0% max.

Output Short Circuit Protection ...............................................…. Continuous

Start up time ……………………………………….………………....…... 1mS typ.

CASE SIP-8:

Bottom View

PIN CONNECTION

Pin

Single

1

2

3

5

-Vin

+Vin

On/Off

NC

All Dimensions In Inches(mm)

X.XX±0.02

X.X±0.5

0.86 [21.8]

0.10 [2.5]

0.70 [17.8]

0.08 [2.0]

0.02 [0.5]

Pin

±0.002

±0.05

Tolerances : Inches

millimeters

Dual

6

7

8

+Vo

-Vo

NC

-Vin

+Vin

On/Off

NC

+Vo

Common

-Vo

1

2

3

5

6

7

8

Typical Derating curve for Natural Convection

-40

100

85

0%

20%

40%

60%

80%

100%

120%

-40

-20

0

20

40

60

80

100

Natural

Convection