AD7450ABRM datasheet(21/28 Pages) AD

21 / 28 page

AD7440/AD7450A

Rev. B | Page 21 of 28

2.5V

+2.5V

–2.5V

0.1

µF

AD7440/

AD7450A

VREF

VIN+

VIN–

VIN

EXTERNAL

VREF (2.5V)

Figure 39. Applying a Bipolar Single-Ended Input to the AD7440/AD7450A

SERIAL INTERFACE

Figure 2 and Figure 3 show detailed timing diagrams for the

serial interface of the AD7450A and the AD7440, respectively.

The serial clock provides the conversion clock and also controls

the transfer of data from the devices during conversion. CS

initiates the conversion process and frames the data transfer.

The falling edge of CS puts the track-and-hold into hold mode

and takes the bus out of three-state. The analog input is sampled

and the conversion is initiated at this point. The conversion

requires 16 SCLK cycles to complete.

Once 13 SCLK falling edges have occurred, the track-and-hold

goes back into track on the next SCLK rising edge, as shown at

Point B in Figure 2 and Figure 3. On the 16th SCLK falling edge,

the SDATA line goes back into three-state. If the rising edge of

CS occurs before 16 SCLKs have elapsed, the conversion

terminates and the SDATA line goes back into three-state.

The conversion result from the AD7440/AD7450A is provided

on the SDATA output as a serial data stream. The bits are

clocked out on the falling edge of the SCLK input. The data

stream of the AD7450A consists of four leading zeros followed

by 12 bits of conversion data provided MSB first; the data

stream of the AD7440 consists of four leading zeros, followed by

the 10 bits of conversion data followed by two trailing zeros,

which is also provided MSB first. In both cases, the output

coding is twos complement.

Sixteen serial clock cycles are required to perform a conversion

and access data from the AD7440/AD7450A. CS going low

provides the first leading zero to be read in by the DSP or

microcontroller. The remaining data is then clocked out on the

subsequent SCLK falling edges beginning with the second

leading zero. Thus, the first falling clock edge on the serial clock

provides the second leading zero. The final bit in the data

transfer is valid on the 16th falling edge, having been clocked

out on the previous (15th) falling edge. Once the conversion is

complete and the data has been accessed after the 16 clock

cycles, it is important to ensure that before the next conversion

is initiated, enough time is left to meet the acquisition and

quiet time specifications (see Timing Examples 1 and 2). To

achieve 1 MSPS with an 18 MHz clock for VDD = 3 V and 5 V, an

18-clock burst performs the conversion and leaves enough time

before the next conversion for the acquisition and quiet time.

In applications with a slower SCLK, it may be possible to read in

data on each SCLK rising edge; that is, the first rising edge of

SCLK after the CS falling edge would have the leading zero

provided and the 15th SCLK edge would have DB0 provided.

tCONVERT

SCLK

12.5(1/FSCLK)

tACQUISITION

1/THROUGHPUT

tQUIET

10ns

Figure 40. Serial Interface Timing Example

AD7450ABRM データシート(PDF) 21 Page - Analog Devices

AD7450ABRM データシート(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

データシートダウンロード