PI3B3863 datasheet(2/3 Pages) PERICOM

2 / 3 page

PS8167D

01/05/00

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012

PI3B3863

3.3V,10-Bit,2-PortBusSwitch

with SSTL-2Enable

DC Electrical Characteristics (Over the Operating Range, TA = 0°C to +70°C, VCC = 3.3V ± 5%)

Parameters Description

Test Conditions(1)

Min.

Typ.(2)

Max.

Units

VIH

Input HIGH Voltage (BE)

Guaranteed Logic HIGH Level

VREF+0.18

VIL

Input LOW Voltage (BE)

Guaranteed Logic LOW Level

-0.3

VREF - 0.18 V

VREF

Input Reference Voltage

1.15

1.25

1.35

IIH

Input HIGH Current

VCC = Max., VIN = VCC

±1

µA

IIL

Input LOW Current

VCC = Max., VIN = GND

±100

µA

IOZH

High Impedance Output Current 0

≤ A, B ≤VCC

±250

µA

VIK

Clamp Diode Voltage

VCC = Min., IIN = –18mA

–1.2

RON

Switch On Resistance(3)

VCC = Min., VIN = 0.8V, ION = 20mA

Ω

& VIN = 1.6V, ION = 15mA

Storage Temperature ...............................................................65°Cto+150°C

Ambient Temperature with Power Applied .............................. 40°Cto+85°C

Supply Voltage to Ground Potential (Inputs & VCC Only) ........0.5Vto+4.6V

Supply Voltage to Ground Potential (Outputs & D/O Only) ......0.5Vto+4.6V

DC Input Voltage .......................................................................0.5Vto+4.6V

DC Output Current .................................................................................120mA

Power Dissipation .................................................................................... 0.5W

Note:

Stresses greater than those listed under MAXIMUM

RATINGSmaycausepermanentdamagetothedevice.

This is a stress rating only and functional operation

of the device at these or any other conditions above

those indicated in the operational sections of this

specification is not implied. Exposure to absolute

maximumratingconditionsforextendedperiodsmay

affectreliability.

Capacitance(TA=25°C,f=1MHz)

Parameters(4)

Description

Test Conditions

Typ.

Units

CIN

Input Capacitance

VIN = 0V

4.5

COFF

A Capacitance, Switch Off

VIN = 0V

3.5

CON(A/B)

A/B Capacitance, Switch On

VIN = 0V

9.5

Notes:

1. ForMax.orMin.conditions,useappropriatevaluespecifiedunderElectricalCharacteristicsfortheapplicabledevicetype.

2. Typical values are at VCC =3.3V,TA=25°Cambientandmaximumloading.

3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined

by the lower of the voltages on the two (A,B) pins.

4. This parameter is determined by device characterization but is not production tested.

MaximumRatings

(Above which the useful life may be impaired. For user guidelines, not tested.)

PI3B3863 データシート(PDF) 2 Page - Pericom Semiconductor Corporation

PI3B3863 データシート(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3

データシートダウンロード

リンク URL

PI3B3863 データシート(PDF) 2 Page - Pericom Semiconductor Corporation

PI3B3863 データシート(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3

データシート ダウンロード

リンク URL

データシートダウンロード