ADE7169ACPZF16 datasheet(46/140 Pages) AD

46 / 140 page

ADE7169F16

Preliminary Technical Data

Rev. PrD | Page 46 of 140

current. Figure 24 shows the principle of a di/dt current sensor.

MAGNETIC FIELD CREATED BY CURRENT

(DIRECTLY PROPORTIONAL TO CURRENT)

+ EMF (ELECTROMOTIVE FORCE)

– INDUCED BY CHANGES IN

MAGNETIC FLUX DENSITY (di/dt)

02875-0-035

Figure 24. Principle of a di/dt Current Sensor

The flux density of a magnetic field induced by a current is

directly proportional to the magnitude of the current. The

changes in the magnetic flux density passing through a

conductor loop generate an electromotive force (EMF) between

the two ends of the loop. The EMF is a voltage signal, which is

proportional to the di/dt of the current. The voltage output

from the di/dt current sensor is determined by the mutual

inductance between the current-carrying conductor and the

di/dt sensor. The current signal needs to be recovered from the

di/dt signal before it can be used. An integrator is therefore

necessary to restore the signal to its original form. The

ADE7169F16 has a built-in digital integrator to recover the

current signal from the di/dt sensor. The digital integrator on

the Current Channel is switched off by default when the

ADE7169F16 is powered up. Setting INTE bit in the MODE1

show the magnitude and phase response of the digital

integrator.

FREQUENCY (Hz)

–10

–20

–30

–40

–50

102

103

02875-0-036

Figure 25. Combined Gain Response of the

Digital Integrator and Phase Compensator

FREQUENCY (Hz)

102

103

02875-0-037

FREQ

–88.0

–88.5

–89.0

–89.5

–90.0

–90.5

Figure 26. Combined Phase Response of the

Digital Integrator and Phase Compensator

FREQUENCY (Hz)

–1.0

–6.0

–1.5

–2.0

–2.5

–3.5

–4.5

–5.5

–3.0

–4.0

–5.0

02875-0-038

Figure 27. Combined Gain Response of the

Digital Integrator and Phase Compensator (40 Hz to 70 Hz)

–89.75

–89.80

–89.85

–89.90

–89.95

–90.00

FREQUENCY (Hz)

–90.05

–89.70

02875-0-039

Figure 28. Combined Phase Response of the

Digital Integrator and Phase Compensator (40 Hz to 70 Hz)

Note that the integrator has a –20 dB/dec attenuation and an

approximately –90° phase shift. When combined with a di/dt

ADE7169ACPZF16 データシート(PDF) 46 Page - Analog Devices

ADE7169ACPZF16 データシート(HTML) 46 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード

リンク URL

ADE7169ACPZF16 データシート(PDF) 46 Page - Analog Devices

ADE7169ACPZF16 データシート(HTML) 46 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシート ダウンロード

リンク URL

データシートダウンロード