 |
データシートサーチシステム |
|
|
データシートサーチシステム |
|
7513 データシート(PDF) 25 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
7513 データシート(HTML) 25 Page - Renesas Technology Corp |
|
|
25 / 66 page  24 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MITSUBISHI MICROCOMPUTERS 7513 Group TIMERS The 7513 group has five timers: timer X, timer Y, timer 1, timer 2, and timer 3. Timer X and timer Y are 16-bit timers, and timer 1, timer 2, and timer 3 are 8-bit timers. All timers are down count timers. When the timer reaches “0016”, an underflow occurs at the next count pulse and the correspond- ing timer latch is reloaded into the timer and the count is continued. When a timer underflows, the interrupt request bit cor- responding to that timer is set to “1”. Read and write operation on 16-bit timer must be performed for both high and low-order bytes. When reading a 16-bit timer, read the high-order byte first. When writing to a 16-bit timer, write the low-order byte first. The 16-bit timer cannot perform the correct operation when reading during the write operation, or when writing during the read operation. Fig. 19 Timer block diagram CNTR0 active edge switch bit Timer 1 count source selection bit Real time port control bit “0” “1” P55/CNTR1 “0” CNTR1 active edge switch bit “10” Timer Y stop control bit Falling edge detection Period measurement mode Timer Y interrupt request Pulse width HL continuously measurement mode Rising edge detection “00”,“01”,“11” Timer Y operating mode bit Timer X interrupt request Timer X mode register write signal P54/CNTR0 Q Q T S P54 direction register Pulse output mode P54 latch Timer X stop control bit “0” “1” Timer X write control bit Q D Latch Q D Latch “1” “0” “1” “10” Timer X operat- ing mode bits “00”,“01”,“11” f(XIN)/16 (f(XCIN)/16 in low-speed mode*) Pulse width measurement mode CNTR0 active edge switch bit Pulse output mode Q Q T S “0” P43 direction register P43 latch “1” TOUT output active edge switch bit Timer 2 write control bit “0” “1” TOUT output control bit “1” P43/ φ/TOUT XCIN Timer 3 count source selection bit “0” “1” Timer 2 interrupt request Timer 3 interrupt request Timer 2 count source selection bit Timer 1 interrupt request Data bus f(XIN)/16(f(XCIN)/16 in low-speed mode*) CNTR0 interrupt request Timer Y operating mode bit “00”,“01”,“10” “11” Real time port control bit “1” P52 latch Real time port control bit “1” P53 latch Timer Y (low) (8) Timer Y (high) (8) Timer 3 latch (8) Timer 3 (8) Timer 1 latch (8) Timer 1 (8) Timer 2 latch (8) Timer 2 (8) Timer X (low) (8) Timer X (high) (8) Timer X (low) latch (8) Timer X (high) latch (8) Timer Y (low) latch (8)Timer Y (high) latch (8) TOUT output control bit “0” “0” “0” P52 P53 P52 direction register P53 direction register P52 data for real time port P53 data for real time port f(XIN)/16 ( f(XCIN)/16 in low-speed mode*) f(XIN)/16 ( f(XCIN)/16 in low-speed mode*) f(XIN)/16 ( f(XCIN)/16 in low-speed mode*) CNTR1 interrupt request * φ = XCIN divided by 2 in low-speed mode |
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか？ [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Japanese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
