M32CSLASH8B datasheet(233/406 Pages) RENESAS

233 / 406 page

Under development

M32C/8B Group

17. Serial Interfaces

Preliminary specification

Specifications in this manual are tentative and subject to change.

REJ09B0450-0050 Rev.0.50 Oct 31, 2008

Page 216 of 385

17.1.2

Clock Asynchronous (UART) Mode

Full-duplex asynchronous serial communications are allowed in this mode. Table 17.3 lists specifications of

UART mode. Table 17.4 lists pin settings. Figure 17.17 shows register settings. Figure 17.18 shows an example

of a transmit operation. Figure 17.19 shows an example of a receive operation.

Table 17.3

UART Mode Specifications

NOTES:

1. Bits CNT3 to CNT0 in the TCSPR register select no division (n = 0) or divide-by-2n (n = 1 to 15).

2. If an overrun error occurs, a read from the UiRB register returns undefined values. The IR bit in the SiRIC

Item

Specification

Data format

• Data length: selectable among 7 bits, 8 bits, or 9 bits long

• Start bit: 1 bit long

• Parity bit: selectable among odd, even, or none

• Stop bit: selectable from 1 bit or 2 bits long

Baud rate

fj / (16 (m + 1))

fj = f1, f8, f2n(1), fEXT

m: setting value of the UiBRG register (00h to FFh)

fEXT: clock input to the CLKi pin when the CKDIR bit in the UiMR register is

set to 1 (external clock)

Transmit/receive control

Selectable among CTS function, RTS function or CTS/RTS function disabled

Transmit start condition

To start transmit operation, all of the following must be met:

• Set the TE bit in the UiC1 register to 1 (transmit operation enabled)

• The TI bit in the UiC1 register is 0 (data in the UiTB register)

• Apply a low-level (“L”) signal to the CTSi pin when the CTS function is selected

Receive start condition

To start receive operation, all of the following must be met:

• Set the RE bit in the UiC1 register to 1 (receive operation enabled)

• The RI bit is 1 (no data in UiRB register) when RTS function is used.

When the above two conditions are met, the RTSi pin output an “L” signal.

• The start bit is detected

Interrupt request generation

timing

Transmit interrupt (The UiIRS bit in the UiC1 register selects one of the following):

• The UiIRS bit is set to 0 (no data in the UiTB register):

when data is transferred from the UiTB register to the UARTi transmit shift register

(transmit operation started)

• The UiIRS bit is set to 1 (transmit operation completed):

when the final stop bit is output from the UARTi transmit shift register

Receive interrupt:

• When data is transferred from the UARTi receive shift register to the UiRB register

(receive operation completed)

Error detection

• Overrun error(2)

Overrun error occurs when the preceding bit of the final stop bit of the next data (the

first stop bit when selecting 2 stop bits) is received before reading the UiRB register

• Framing error

Framing error occurs when the number of the stop bits set by the STPS bit in the

UiMR register is not detected

• Parity error

Parity error occurs when parity is enabled and the received data does not have the

correct even or odd parity set by the PRY bit in the UiMR register.

• Error sum flag

Error sum flag is set to 1 when any of overrun, framing, and parity errors occurs

Selectable function

• LSB first or MSB first

Data is transmitted or received from either bit 0 or bit 7

• Serial data logic inverse

Transmit and receive data are logically inverted. The start bit and stop bit are not

inverted

• TXD and RXD I/O polarity inverse

The level output from the TXD pin and the level applied to the RXD pin are inverted.

All the data including the start bit and stop bit are inverted.

M32C/8B データシート(PDF) 233 Page - Renesas Technology Corp

M32C/8B データシート(HTML) 233 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード