IMP38C42SLASHD datasheet(4/10 Pages) A1PROS

4 / 10 page

IMP38C/HC/42/3/4/5

408-432-9100/www.impweb.com

Absolute Maximum Ratings

VCC Supply Voltage . . . . . . . . . . . . . . . . . . . . . . 20V

VCC Supply Current . . . . . . . . . . . . . . . . . . . . . . 30mA

IOUT Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0A

Current-Sense and Feedback Inputs . . . . . . . . 0.3V to 5.5V

Operation Junction Temperature . . . . . . . . . . . +150

°C

Storage Temperature . . . . . . . . . . . . . . . . . . . . . – 65

°C to +150°C

Lead Soldering Temperature (10 seconds) . . . +300

°C

Parameter

Symbol

Conditions

Min

Typ

Max

Units

Reference

Output voltage

VREF

TA = +25

°C, IO = 1mA

4.90

5.00

5.10

Line Regulation

12V

≤ VCC ≤ 18V, IOUT = 5µA2

Load Regulation

1mA

≤ IO ≤ 20mA

Temperature Stability

TCREF

Note 1

0.2

mV/

°C

Total Reference Variation

Line, Load, Temperature, Note 1

4.82

5.18

Output Noise Voltage

10Hz

≤ f ≤ 10kHz, TA = +25°C, Note 1

µV

Long Term Stability

TA = 125

°C, 1000 Hours, Note 1

TBD

Output Short Circuit

ISC

– 30

– 40

– 180

Oscillator Section

Initial Accuracy

fINIT

TA = 25

°C, Note 5

kHz

Voltage Stability

12V

≤ VCC ≤ 18V

0.2

1.0

Temperature Stability

TCOSC

Note 1

0.04

°C

Discharge Current

VRT/CT = 2V

7.2

8.4

12.0

Amplitude peak-to-peak

VOSC, P-P

VRT/CT peak-to-peak

1.1

1.7

2.3

Error Amplifier Section

Input Voltage

VIN

VCOMP = 2.5V

2.45

2.50

2.55

Input Bias Current

VFB = 4.5V

–11

µA

Open Loop Gain

AVOL

≤ VO ≤ 4V, Note 1

Unity Gain Bandwidth

UGBW

Note1

0.7

1.0

MHz

Power Supply Rejection Ratio

PSRR

VSTART

≤ VCC ≤ VCCMAX

Output Sink Current

IOL

VFB = 2.7V, Vcomp = 1.1V

Output Source Current

IOH

VFB = 2.3V, Vcomp = 5.0V

– 0.5

– 1.0

VOUT High

VOH

VFB = 2.3V, RL = 15k

Ω to ground

4.5

4.6

5.0

VOUT Low

VOL

VFB = 2.7V, RL = 15k

Ω to VREF

0.30

0.50

Unless otherwise noted, VCC = 15V, RT = 10k

Ω and CT = 3.3nF. Specifications are over the – 40°C to +85°C ambient temperature range.

Bold/blue

specifications indicate enhanced performance features.

Electrical Characteristics

Package Thermal Resistance

8-Pin Plastic DIP (

θJA) . . . . . . . . . . . . . . . . . 125°C/W

8-Pin MicroSO (

θJA) . . . . . . . . . . . . . . . . . . . 250°C/W

8-Pin SO (

θJA) . . . . . . . . . . . . . . . . . . . . . . . . 170°C/W

14-Pin Plastic DIP (

θJA) . . . . . . . . . . . . . . . . 90°C/W

14-Pin SO (

θJA) . . . . . . . . . . . . . . . . . . . . . . . 145°C/W

Note: All voltages are referenced to GND.

These are stress ratings only and functional operation is not

implied. Exposure to absolute maximum ratings for prolonged

time periods may affect device reliability.

IMP38C42/D データシート(PDF) 4 Page - A1 PROs co., Ltd.

IMP38C42/D データシート(HTML) 4 Page - A1 PROs co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10

データシートダウンロード