| データシートサーチシステム |
|
TMS3471CFS データシート(PDF) 12 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMS3471CFS データシート(HTML) 12 Page - Texas Instruments |
|
12 / 18 page ![]() TC241 780- × 488-PIXEL CCD IMAGE SENSOR SOCS006C – AUGUST 1986 – REVISED DECEMBER 1991 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 optical characteristics, TA = 40°C (unless otherwise noted) PARAMETER MIN TYP MAX UNIT Sensitivity No IR filter Measured at VU 150 mV/lx Sensitivity With IR filter U (see Notes 10 and 11) 19 mV/lx Saturation signal, Vsat (see Note 12) Antiblooming disabled, interlace off 320 400 mV Maximum usable signal, Vuse Antiblooming enabled, interlace on 180 360 mV Blooming overload ratio (see Note 13) Interlace on 100 Blooming-overload ratio (see Note 13) Interlace off 200 Image-area well capacity 200 x 103 electrons Smear (see Note 14) See Note 15 0.00072 Dark current Interlace off TA = 21°C 0.027 nA/cm2 Dark signal (see Note 16) TC241-30 15 mV Dark signal (see Note 16) TC241-40 20 mV Pixel uniformity Output signal = 50 mV ±10 mV TC241-30 3.5 mV Pixel uniformity Output signal = 50 mV ±10 mV TC241-40 5 mV Column uniformity Output signal = 50 mV ±10 mV TC241-30 0.5 mV Column uniformity Output signal = 50 mV ±10 mV TC241-40 0.7 mV Shading Output signal = 100 mV 15% NOTES: 10. Sensitivity is measured at an integration time of 16.667 ms with a source temperature of 2856 K. A CM-500 filter is used. 11. VU is the output voltage that represents the threshold of operation of antiblooming. VU ≈ 1/2 saturation signal. 12. Saturation is the condition in which further increase in exposure does not lead to further increase in output signal. 13. Blooming-overload ratio is the ratio of blooming exposure to saturation exposure. 14. Smear is a measure of the error induced by transferring charge through an illuminated pixel in shutterless operation. It is equivalent to the ratio of the single-pixel transfer time during a fast dump to the exposure time using an illuminated section that is 1/10 of the image-area vertical height with recommended clock frequencies. 15. Exposure time is 16.67 ms and the fast-dump clocking rate during vertical timing is 2.05 MHz. 16. Dark-signal level is measured from the dummy pixels. |
|
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |