| データシートサーチシステム |
|
REF5025A データシート(PDF) 10 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
REF5025A データシート(HTML) 10 Page - Texas Instruments |
|
10 / 19 page ![]() R5 60kW REF50xx TEMP V OUT GND TRIM/NR V IN aT aT (10 A m at+25 C) ° R2 R1 R3 R4 10kW 1kW 1.2V DNC TEMP V OUT V IN GND DNC NC TRIM/NR REF50xx +V SUPPLY 10kW 1kW 470W DNC TEMP V OUT V IN GND DNC NC TRIM/NR REF50xx C BYPASS 1 Fto10 F m m C L 1 Fto50 F m m +V SUPPLY V OUT DNC TEMP V OUT V IN GND DNC NC TRIM/NR REF50xx C1 1 F m +V SUPPLY REF5020-Q1, REF5025-Q1, REF5030-Q1 REF5040-Q1, REF5045-Q1, REF5050-Q1 SBOS456F – SEPTEMBER 2008 – REVISED SEPTEMBER 2011 www.ti.com APPLICATION INFORMATION The REF50xx is family of low-noise, precision requirement of 2.7 V, these references can be bandgap voltage references that are specifically operated with a supply of 200 mV above the output designed for excellent initial voltage accuracy and voltage in an unloaded condition. For loaded drift. Figure 28 shows a simplified block diagram of conditions, a typical dropout voltage versus load plot the REF50xx. is shown in Figure 6 of the Typical Characteristics. USING THE TRIM/NR PIN The REF50xx provides a very accurate voltage output. However, VOUT can be adjusted to reduce noise and shift the output voltage from the nominal value by configuring the trim and noise reduction pin (TRIM/NR, pin 5). The TRIM/NR pin provides a ±15-mV adjustment of the device bandgap, which produces a ±15-mV change on the VOUT pin. Figure 30 shows a typical circuit using the TRIM/NR pin to adjust VOUT. When using this technique, the temperature coefficients of the resistors can degrade the temperature drift at the output. Figure 28. REF50xx Simplified Block Diagram BASIC CONNECTIONS Figure 29 shows the typical connections for the REF50xx. A supply bypass capacitor ranging between 1 μF to 10 μF is recommended. A 1-μF to 50- μF, low-ESR output capacitor (CL) must be connected from VOUT to GND. The ESR value should Figure 30. VOUT Adjustment Using TRIM/NR Pin be less than or equal to 1.5 Ω. The ESR minimizes gain peaking of the internal 1.2-V reference and thus The REF50xx allows access to the bandgap through reduces noise at the VOUT pin. the TRIM/NR pin. Placing a capacitor from the TRIM/NR pin to GND (as Figure 31 illustrates) in combination with the internal 1-k Ω resistor creates a low-pass filter that lowers the overall noise measured on the VOUT pin. A capacitance of 1 μF is suggested for a low-pass filter with a corner frequency of 14.5 Hz. Higher capacitance results in a lower cutoff frequency. Figure 29. Basic Connections SUPPLY VOLTAGE The REF50xx family of voltage references features extremely low dropout voltage. With the exception of the REF5020, which has a minimum supply Figure 31. Noise Reduction Using TRIM/NR Pin 10 Submit Documentation Feedback Copyright © 2008–2011, Texas Instruments Incorporated |
|
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |