AD9240AS datasheet(12/24 Pages) AD

12 / 24 page

AD9240

REV. A

–12–

REFERENCE OPERATION

The AD9240 contains an onboard bandgap reference that pro-

vides a pin-strappable option to generate either a 1 V or 2.5 V

output. With the addition of two external resistors, the user can

generate reference voltages other than 1 V and 2.5 V. Another

alternative is to use an external reference for designs requiring

enhanced accuracy and/or drift performance. See Table II for a

summary of the pin-strapping options for the AD9240 reference

configurations.

Figure 29 shows a simplified model of the internal voltage

reference of the AD9240. A pin-strappable reference ampli-

fier buffers a 1 V fixed reference. The output from the refer-

ence amplifier, A1, appears on the VREF pin. The voltage on

the VREF pin determines the full-scale input span of the A/D.

This input span equals,

Full-Scale Input Span = 2

× VREF

The voltage appearing at the VREF pin as well as the state of

the internal reference amplifier, A1, are determined by the volt-

age appearing at the SENSE pin. The logic circuitry contains

two comparators which monitor the voltage at the SENSE pin.

The comparator with the lowest set point (approximately 0.3 V)

controls the position of the switch within the feedback path of

A1. If the SENSE pin is tied to REFCOM, the switch is con-

nected to the internal resistor network thus providing a VREF of

2.5 V. If the SENSE pin is tied to the VREF pin via a short or

resistor, the switch is connected to the SENSE pin. A short will

provide a VREF of 1.0 V while an external resistor network will

provide an alternative VREF between 1.0 V and 2.5 V.

The second comparator controls internal circuitry that will

disable the reference amplifier if the SENSE pin is tied AVDD.

Disabling the reference amplifier allows the VREF pin to be

driven by an external voltage reference.

LOGIC

DISABLE

7.5k

LOGIC

DISABLE

A/D

AD9240

CAPT

CAPB

VREF

SENSE

REFCOM

Figure 29. Equivalent Reference Circuit

The actual reference voltages used by the internal circuitry of

the AD9240 appear on the CAPT and CAPB pins. For proper

operation when using the internal or an external reference, it is

necessary to add a capacitor network to decouple these pins.

Figure 30 shows the recommended decoupling network. This

capacitive network performs the following three functions: (1)

along with the reference amplifier, A2, it provides a low source

impedance over a large frequency range to drive the A/D inter-

nal circuitry, (2) it provides the necessary compensation for A2

and (3) it bandlimits the noise contribution from the reference.

The turn-on time of the reference voltage appearing between

CAPT and CAPB is approximately 15 ms and should be evalu-

ated in any power-down mode of operation.

0.1 F

10 F

0.1 F

CAPT

CAPB

AD9240

Figure 30. Recommended CAPT/CAPB Decoupling Network

The A/D’s input span may be varied dynamically by changing

the differential reference voltage appearing across CAPT and

CAPB symmetrically around 2.5 V (i.e., midsupply). To change

the reference at speeds beyond the capabilities of A2, it will be

necessary to drive CAPT and CAPB with two high speed, low

noise amplifiers. In this case, both internal amplifiers (i.e., A1

and A2) must be disabled by connecting SENSE to AVDD and

VREF to REFCOM and the capacitive decoupling network

removed. The external voltages applied to CAPT and CAPB

must be 2.5 V + Input Span/4 and 2.5 V – Input Span/4, respec-

tively, where the input span can be varied between 2 V and 5 V.

Note that those samples within the pipeline A/D during any

reference transition will be corrupted and should be discarded.

AD9240AS データシート(PDF) 12 Page - Analog Devices

AD9240AS データシート(HTML) 12 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

データシートダウンロード

リンク URL

AD9240AS データシート(PDF) 12 Page - Analog Devices

AD9240AS データシート(HTML) 12 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

データシート ダウンロード

リンク URL

データシートダウンロード