DOC7707 datasheet(44/307 Pages) ETC1

44 / 307 page

7707F–AVR–11/10

AT90USB82/162

• Bit 4 - Res: Reserved bit

This bit is reserved and will always read as zero.

• Bit 3 - PRTIM1: Power Reduction Timer/Counter1

Writing a logic one to this bit shuts down the Timer/Counter1 module. When the Timer/Counter1

is enabled, operation will continue like before the shutdown.

• Bit 2 - PRSPI: Power Reduction Serial Peripheral Interface

Writing a logic one to this bit shuts down the Serial Peripheral Interface by stopping the clock to

the module. When waking up the SPI again, the SPI should be re initialized to ensure proper

operation.

• Bit 1 - Res: Reserved bit

These bits are reserved and will always read as zero.

• Bit 0 - Res: Reserved bit

These bits are reserved and will always read as zero.

8.6.2

Power Reduction Register 1 - PRR1

• Bit 7 - PRUSB: Power Reduction USB

Writing a logic one to this bit shuts down the USB by stopping the clock to the module. When

waking up the USB again, the USB should be re initialized to ensure proper operation.

• Bit 6..1 - Res: Reserved bits

These bits are reserved and will always read as zero.

• Bit 0 - PRUSART1: Power Reduction USART1

Writing a logic one to this bit shuts down the USART1 by stopping the clock to the module.

When waking up the USART1 again, the USART1 should be re initialized to ensure proper

operation.

8.7

Minimizing Power Consumption

There are several issues to consider when trying to minimize the power consumption in an AVR

controlled system. In general, sleep modes should be used as much as possible, and the sleep

mode should be selected so that as few as possible of the device’s functions are operating. All

functions not needed should be disabled. In particular, the following modules may need special

consideration when trying to achieve the lowest possible power consumption.

8.7.1

Analog Comparator

When entering Idle mode, the Analog Comparator should be disabled if not used. In other sleep

modes, the Analog Comparator is automatically disabled. However, if the Analog Comparator is

set up to use the Internal Voltage Reference as input, the Analog Comparator should be dis-

abled in all sleep modes. Otherwise, the Internal Voltage Reference will be enabled,

Bit

654

PRUSB

–

PRUSART1

PRR1

Read/Write

R/W

Initial Value

DOC7707 データシート(PDF) 44 Page - List of Unclassifed Manufacturers

DOC7707 データシート(HTML) 44 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード

リンク URL

DOC7707 データシート(PDF) 44 Page - List of Unclassifed Manufacturers

DOC7707 データシート(HTML) 44 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシート ダウンロード

リンク URL

データシートダウンロード