• North America Tel: 800.366.2266 / Fax: 978.366.2266

• Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300

• Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298

Visit www.macomtech.com for additional data sheets and product information.

M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make

changes to the product(s) or information contained herein without notice.

2

Low Noise CATV Amplifier

50 - 1000 MHz

Rev. V2

MAAMSS0067

ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions

is considering for development. Performance is based on target specifications, simulated results,

and/or prototype measurements. Commitment to develop is not guaranteed.

PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology

Solutions has under development. Performance is based on engineering tests. Specifications are

typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available.

Commitment to produce in volume is not guaranteed.

Parameter

Test Conditions

Units

Min.

Typ.

Max.

Gain

—

dB

11.5

12.2

13.0

Gain Flatness

—

dB

—

0.4

1.0

Noise Figure

—

dB

—

3.3

4.0

Input VSWR

—

Ratio

—

1.3:1

—

Output VSWR

—

Ratio

—

1.5:1

—

Output IP3

Two tones at 397 & 403 MHz, +4 dBm output per tone

dBm

—

32

—

Composite Triple Beat, CTB

135 Channels, +13 dBmV/Channel at the input

dBc

—

-78

-70

Composite Second Order, CSO

135 Channels, +13 dBmV/Channel at the input

dBc

—

-78

-70

Cross modulation

135 Channels, +13 dBmV/Channel at the input

dBc

—

-73

-64

P1dB

400 MHz

dBm

—

24

—

+5 Volts

mA

—

190

225

Test Circuit with M/A-COM Balun ETN1-1-13

Handling Procedures

Please observe the following precautions to avoid

damage:

Static Sensitivity

Gallium Arsenide Integrated Circuits are sensitive

to electrostatic discharge (ESD) and can be

damaged by static electricity. Proper ESD control

techniques should be used when handling these

devices.

Qty

Description

8

Capacitor, 0.01 uF, 0603, SMT, 10% (C1-C8)

2

Capacitor, 2 pF, 0402, SMT, ± 0.25pF (C9-C10)

2

Inductor, 390 nH, 1008, SMT, 10% (L1, L2)

2

Balun, 1:1, M/A-COM, ETN1-1-13, SMT (T1,T2)

2

Resistor, 0 ohms, 0603, SMT (R1, R2)

External Circuitry Parts List

Test Circuit Schematic

5

5. The 1:1 baluns, T1 & T2, are M/A-COM part number

ETN1-1-13.

RF IN

T1

T2

C2

C7

C8

L2

C6

L1

C5

+5V

+5V

C3

C4

C1

RF

OUT

R2

R1

C9

C10

RF IN

T1

T2

C2

C7

C8

L2

C6

L1

C5

+5V

+5V

C3

C4

C1

RF

OUT

R2

R1

C9

C10

6. Reference M/A-COM Application Note S2083 for

recommended PCB configuration. R1 and R2 are 0 ohms.

Recommended Test Circuit Layout

6