Page 2 of 3

www.pduke.com

2013/5/3

TEN06 SERIES

6 WATTS

DC-DC CONVERTER

Output Current

Model

Number

Input

Range

Output

Voltage

Output

Voltage Range Min. load Full load

Output

(2)

Ripple & Noise

No Load

(3)

Input Current

Eff

(4)

(%)

Capacitor

(5)

Load max

TEN06-05S33 4.5 ~ 9 VDC

3.3 VDC

2.84 ~ 3.67 VDC

0mA

1200mA

100mVp-p

80mA

74

6600µF

TEN06-05S05 4.5 ~ 9 VDC

5 VDC

4.3 ~ 6 VDC

0mA

1000mA

100mVp-p

65mA

77

3000µF

TEN06-05S12 4.5 ~ 9 VDC

12 VDC

12 ~ 15 VDC

0mA

500mA

100mVp-p

140mA

83

1400µF

TEN06-05D12 4.5 ~ 9 VDC ±12 VDC

±12 ~ ±15 VDC

0mA

±250mA

100mVp-p

140mA

83

±510µF

TEN06-12S33 9 ~ 18 VDC

3.3 VDC

2.84 ~ 3.67 VDC

0mA

1500mA

100mVp-p

45mA

76

6600µF

TEN06-12S05 9 ~ 18 VDC

5 VDC

4.3 ~ 6 VDC

0mA

1200mA

100mVp-p

55mA

80

3000µF

TEN06-12S12 9 ~ 18 VDC

12 VDC

12 ~ 15 VDC

0mA

500mA

100mVp-p

60mA

85

1400µF

TEN06-12D12 9 ~ 18 VDC

±12 VDC

±12 ~ ±15 VDC

0mA

±250mA

100mVp-p

55mA

85

±510µF

TEN06-24S33 18 ~ 36 VDC 3.3 VDC

2.84 ~ 3.67 VDC

0mA

1500mA

100mVp-p

15mA

77

6600µF

TEN06-24S05 18 ~ 36 VDC

5 VDC

4.3 ~ 6 VDC

0mA

1200mA

100mVp-p

20mA

82

3000µF

TEN06-24S12 18 ~ 36 VDC

12 VDC

12 ~ 15 VDC

0mA

500mA

100mVp-p

30mA

85

1400µF

TEN06-24D12 18 ~ 36 VDC ±12 VDC

±12 ~ ±15 VDC

0mA

±250mA

100mVp-p

30mA

85

±510µF

TEN06-48S33 36 ~ 75 VDC 3.3 VDC

2.84 ~ 3.67 VDC

0mA

1500mA

100mVp-p

15mA

77

6600µF

TEN06-48S05 36 ~ 75 VDC

5 VDC

4.3 ~ 6 VDC

0mA

1200mA

100mVp-p

15mA

80

3000µF

TEN06-48S12 36 ~ 75 VDC

12 VDC

12 ~ 15 VDC

0mA

500mA

100mVp-p

20mA

85

1400µF

TEN06-48D12 36 ~ 75 VDC ±12 VDC

±12 ~ ±15 VDC

0mA

±250mA

100mVp-p

15mA

85

±510µF

TEN06-48S05 Derating Curve

TEN06-48S05 Efficiency VS Input Voltage

TEN06-48S05 Efficiency VS Output Current

Figure 1

Note:

1.

BELLCORE TR-NWT-000332. Case 1:50% Stress, temperature at 40ºC.

MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment).

2.

Typical value at nominal input and full load.

3.

Typical value at nominal input and no load.

4.

Typical value at nominal input and full load.

5.

Test by minimum input and constant resistive load.

6.

The following output voltage can be obtained by connecting this terminal to an output + or – terminal. Unless the

output voltage is adjusted, this terminal should be open.

7.

In addition, the voltage can be adjusted not by shorting these terminals, but by connecting them to resistances as

shown below.

8.

Arithmetic expression connected resistance: R ( k

)

8-1 Vo=(3.3*R+36.7)/(R+10)

8-2 Vo=(3.3*R+36.7)/(R+12.92)

8-3 Vo=2.5*[2+2.7/(R+6.8)]

8-4 Vo=2.5*[2-2.7/(R+9.5)]

8-5 Vo=2.5+9.5(R+10.9)/(R+8.2) [Between two outputs] 8-6 Vo=2.5+22*(R+12.7)/(R+10) [Between two outputs]

9.

The TEN06 series standard module meets EN55022 Class A and Class B with external components.

For more detail information, please contact with P-DUKE.

CAUTION: This power module is not internally fused. An input line fuse must always be used.