 |
データシートサーチシステム |
|
|
データシートサーチシステム |
|
LM7341 データシート(PDF) 4 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM7341 データシート(HTML) 4 Page - Texas Instruments |
|
|
4 / 27 page  LM7341 SNOSAW9B – MAY 2008 – REVISED MARCH 2013 www.ti.com ±5V Electrical Characteristics Unless otherwise specified, all limits ensured for TA = 25°C, V + = +5V, V− = −5V, V CM = VOUT = 0V and RL > 1 MΩ to 0V. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min(1) Typ(2) Max(1) Units VOS Input Offset Voltage VCM = −4.5V and VCM = 4.5V −4 ±0.2 +4 mV −5 +5 TCVOS Input Offset Voltage Temperature Drift ±2 μV/°C IB Input Bias Current VCM = −4.5V −200 −95 −250 nA VCM = 4.5V 35 70 80 IOS Input Offset Current VCM = −4.5V and VCM = 4.5V 1 40 nA 50 CMRR Common Mode Rejection Ratio −5V ≤ VCM ≤ 3V 84 112 82 dB −5V ≤ VCM ≤ 5V 72 92 70 PSRR Power Supply Rejection Ratio 2.7V ≤ VS ≤ 30V, VCM = −4.5V 86 106 dB 84 CMVR Common Mode Voltage Range CMRR ≥ 65 dB −5.3 −5.0 V 5.0 5.3 AVOL Open Loop Voltage Gain −4V ≤ VO ≤ 4V 20 110 V/mV RL = 10 kΩ to 0V 12 VOUT Output Voltage Swing RL = 10 kΩ to 0V, 80 150 High VID = 100 mV 200 RL = 2 kΩ to 0V, 170 300 VID = 100 mV 400 mV from either rail Output Voltage Swing RL = 10 kΩ to 0V 90 150 Low VID = −100 mV 200 RL = 2 kΩ to 0V 210 300 VID = −100 mV 400 IOUT Output Current Sourcing, VOUT = −5V 6 11 VID = 200 mV 4 mA Sinking, VOUT = 5V 6 12 VID = −200 mV 4 IS Supply Current VCM = −4.5V and VCM = 4.5V 0.65 1.0 mA 1.1 SR Slew Rate ±4V Step 1.7 V/ μs GBW Gain Bandwidth f = 100 kHz, RL = 100 kΩ 4.0 MHz en Input Referred Voltage Noise Density f = 1 kHz 33 nV/ √Hz in Input Referred Voltage Noise Density f = 1 kHz 0.26 pA/ √Hz THD+N Total Harmonic Distortion + Noise f = 10 kHz −66 dB tPD Propagation Delay Overdrive = 50 mV(3) 8 µs Overdrive = 1V(3) 6 tr Rise Time 20% to 80%(3) 5 µs tf Fall Time 80% to 20%(3) 5 µs (1) All limits are specified by testing or statistical analysis. (2) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. (3) The maximum differential voltage between the input pins is VIN Differential = ±15V. 4 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM7341 |
|
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか？ [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Japanese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
