ATmega16 datasheet(98/315 Pages) ATMEL

98 / 315 page

ATmega16(L)

2466E–AVR–10/02

seting (or clearing) the OC1x Register at the compare match between OCR1x and

TCNT1, and clearing (or setting) the OC1x Register at the timer clock cycle the counter

is cleared (changes from TOP to BOTTOM).

The PWM frequency for the output can be calculated by the following equation:

The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).

The extreme values for the OCR1x Register represents special cases when generating

a PWM waveform output in the fast PWM mode. If the OCR1x is set equal to BOTTOM

(0x0000) the output will be a narrow spike for each TOP+1 timer clock cycle. Setting the

OCR1x equal to TOP will result in a constant high or low output (depending on the polar-

ity of the output set by the COM1x1:0 bits.)

A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved

by setting OC1A to toggle its logical level on each compare match (COM1A1:0 = 1).

This applies only if OCR1A is used to define the TOP value (WGM13:0 = 15). The wave-

form generated will have a maximum frequency of f

OC1A = fclk_I/O/2 when OCR1A is set to

zero (0x0000). This feature is similar to the OC1A toggle in CTC mode, except the dou-

ble buffer feature of the output compare unit is enabled in the fast PWM mode.

Phase Correct PWM Mode

The phase correct Pulse Width Modulation or phase correct PWM mode (WGM13:0 =

1,2,3,10, or 11) provides a high resolution phase correct PWM waveform generation

option. The phase correct PWM mode is, like the phase and frequency correct PWM

mode, based on a dual-slope operation. The counter counts repeatedly from BOTTOM

(0x0000) to TOP and then from TOP to BOTTOM. In non-inverting Compare Output

mode, the Output Compare (OC1x) is cleared on the compare match between TCNT1

and OCR1x while upcounting, and set on the compare match while downcounting. In

inverting Output Compare mode, the operation is inverted. The dual-slope operation has

lower maximum operation frequency than single slope operation. However, due to the

symmetric feature of the dual-slope PWM modes, these modes are preferred for motor

control applications.

The PWM resolution for the phase correct PWM mode can be fixed to 8-, 9-, or 10-bit, or

defined by either ICR1 or OCR1A. The minimum resolution allowed is 2-bit (ICR1 or

OCR1A set to 0x0003), and the maximum resolution is 16-bit (ICR1 or OCR1A set to

MAX). The PWM resolution in bits can be calculated by using the following equation:

In phase correct PWM mode the counter is incremented until the counter value matches

either one of the fixed values 0x00FF, 0x01FF, or 0x03FF (WGM13:0 = 1, 2, or 3), the

value in ICR1 (WGM13:0 = 10), or the value in OCR1A (WGM13:0 = 11). The counter

has then reached the TOP and changes the count direction. The TCNT1 value will be

equal to TOP for one timer clock cycle. The timing diagram for the phase correct PWM

mode is shown on Figure 47. The figure shows phase correct PWM mode when OCR1A

or ICR1 is used to define TOP. The TCNT1 value is in the timing diagram shown as a

histogram for illustrating the dual-slope operation. The diagram includes non-inverted

and inverted PWM outputs. The small horizontal line marks on the TCNT1 slopes repre-

sent compare matches between OCR1x and TCNT1. The OC1x interrupt flag will be set

when a compare match occurs.

OCn xPW M

clk_I/O

TOP

()

⋅

-----------------------------------

PCPW M

TOP

()

log

()

log

-----------------------------------

ATMEGA16 データシート(PDF) 98 Page - ATMEL Corporation

ATMEGA16 データシート(HTML) 98 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード