VRG8653 datasheet(3/9 Pages) AEROFLEX

3 / 9 page

SCD8653 Rev D 4/10/14

Aeroflex Plainview

RH1185 Negative LDO section only 9/

Reference Voltage

(At pin 6) 2/

VREF

1mA < IOUT < 3A, VIN - VOUT = 1.2V to 28V, VOUT = -5V -2.29

-2.45

Dropout Voltage 2/, 6/

VDROP

IOUT = 0.5A, VOUT = -5V

-0.425

IOUT = 3A, VOUT = -5V

-1.05

Line Regulation 2/, 10/1.0V < VIN - VOUT < 20V, VOUT = -5V

0.02

%/V

Load Regulation 2/, 10/5mA < IOUT < 3A, VIN - VOUT = 1.5V to 10V, VOUT = -5V

0.8

Minimum Input Voltage 2/,

VIN MIN IOUT = 3A , VOUT = VREF

-4.50

Internal Current Limit (See

Graph for Guaranteed

Curve - See Figure 6) 2/,

13/

ICL

1.5V < VIN - VOUT < 10V

3.3

4.55

VIN - VOUT = 15V

2.0

4.5

VIN - VOUT = 20V

1.0

3.1

External Current Limit 2/

ILIM

RLIM = 5K

, (VIN - VOUT) = 1.5V 12/

2.7

3.7

RLIM = 15K

, (VIN - VOUT) = 1.5V 12/

0.9

1.6

Quiescent Supply Current

2/, 8/

IOUT = 5mA, VOUT = VREF, -4V < VIN < -25V

3.5

Supply Current

Change with Load 2/



VIN – VOUT = VSAT 11/-

mA/A

VIN – VOUT

 2V

-21

mA/A

Ripple Rejection

IOUT = 0.5A, VIN - VOUT = 3V, f = 120Hz,

Notes

1/ The manufacturer’s output current rating for the RH1084MK positive regulator integrated circuit is 5.0 Amps. For Compliance

with the Current Density specification of MIL-STD-883 Rev. C, the electrical performance characteristics are specified at an

output current of 3.0 Amps.

2/ Specification derated to reflect total dose exposure to 100krads (Si) at +25°C.

3/ Line and load regulation are guaranteed up to the maximum power dissipation of 25W. Power dissipation is determined by the

input/output differential voltage and the output current. Guaranteed maximum power dissipation will not be available over the

full input/output voltage range.

4/ Dropout voltage is specified over the full output current range of the device.

5/ Not tested. Shall be guaranteed by design, characterization, or correlation to other tested parameters.

6/ Dropout voltage is tested by reducing input voltage until the output drops 1% below its nominal value. Tests are done at 0.5A

and 3A. The power transistor looks basically like a pure resistance in this range so that minimum differential at any

intermediate current can be calculated by interpolation; VDROPOUT = 0.25V + (0.25

 x IOUT). For load current less than 0.5A,

see Figure 4.

7/ “Minimum input voltage” is limited by base emitter voltage drive of the power transistor section, not saturation as measured in

Note 6. For output voltages below 4V, “minimum input voltage” specification may limit dropout voltage before transistor

saturation limitation.

8/ Supply current is measured on the ground pin, and does not include load current, RLIM, or output divider current.

9/ The 25W power level is guaranteed for an input-output voltage of 8.3V to 17V. At lower voltages the 3A limit applies, and at

higher voltages the internal power limiting may restrict regulator power below 25W.

10/ Line and load regulation are measured on a pulse basis with a pulse width of 2ms, to minimize heating. DC regulation will be

affected by thermal regulation and temperature coefficient of the reference.

11/VSAT is the maximum specified dropout voltage; 0.25V +(0.25

 x IOUT).

12/ Current limit is programmed with a resistor from REF pin to GND pin. RLIM = 15K

/ILIM.

13/ Pulsed @ <10% duty cycle @ +25°C

ELECTRICAL PERFORMANCE CHARACTERISTICS (continued)

UNLESS OTHERWISE SPECIFIED: -55°C

TC+125°C

Parameter

Symbol

Conditions (P

 PMAX)

Min

Max

Units

VOUT

VIN

VOUT

IOUT

VRG8653 データシート(PDF) 3 Page - Aeroflex Circuit Technology

VRG8653 データシート(HTML) 3 Page - Aeroflex Circuit Technology

Html Pages

1 2 3 4 5 6 7 8 9

データシートダウンロード