AX-SIGFOX-API datasheet(11/19 Pages) ONSEMI

11 / 19 page

AX−SIGFOX

www.onsemi.com

COMMAND INTERFACE

General Information

The chapter “Command Interface” is a documentation of

the AT−Command set for devices which do not have an

API−interface. To see whether the device is capable of

receiving AT−Commands, please refer to chapter “Part

Numbers”. If the device has been shipped with the

API−Interface, please refer to the AX−Sigfox SOFTWARE

MANUAL for an introduction on how to setup a project and

how to use the API−Interface.

Serial Parameters: 9600, 8, N, 1

The AX−Sigfox uses the UART (pins UARTTX,

UARTRX) to communicate with a host and uses a bitrate of

9600 baud, no parity, 8 data bits and one stop bit.

Power Modes

Standby

After Power−Up and after finishing a SIGFOX

transmission, AX−Sigfox enters Standby mode. In Standby

mode, AX−Sigfox listens on the UART for commands from

the host. Also, OOB frames are transmitted whenever the

OOB timer fires. To conserve power, the AX−Sigfox can be

put into Sleep or turned off (Deep Sleep) completely.

Sleep

The command AT$P=1 is used to put the AX−Sigfox into

Sleep mode. In this mode, only the wakeup timer for

out−of−band messages is still running. To wake the

AX−Sigfox up from Sleep mode toggle the serial UARTRX

pin, e.g. by sending a break (break is an RS232 framing

violation, i.e. at least 10 bit durations low). When an Out of

Band (OOB) message is due, AX−Sigfox automatically

wakes up to transmit the message, and then returns to Sleep

mode.

Deep Sleep

In Deep Sleep mode, the AX−Sigfox is completely turned

off and only draws negligible leakage current. Deep Sleep

mode can be activated with AT$P=2. To wake−up from

Deep Sleep mode, GPIO9 is pulled to GND.

When using Deep Sleep mode, keep two things in mind:

Everything is turned off, timers are not running at all and all

settings will be lost (use AT$WR to save settings to flash

before entering Deep Sleep mode). Out−of−band messages

will therefore not be sent. The pins states are frozen in Deep

Sleep mode. The user must ensure that this will not result in

condition which would draw a lot of current.

AT Commands

Numerical Syntax

hexdigit ::= [0−9A−Fa−f]

hexnum ::= “0x” hexdigit+

decnum ::= “0” | [1−9] [0−9]*

octnum ::= “0” [0−7]+

binnum ::= “0b” [01]+

bit

::= [01]

optnum ::= “−1”

frame

::= (hexdigit hexdigit)+

uint

::= hexnum | decnum | octnum | binnum

uint_opt ::= uint | optnum

Command Syntax

A command starts with ‘AT’ (everything is case

sensitive!), continues with the actual command followed by

parameters (if any) and ends with any kind of whitespace

(space, tab, newline etc.)

If incorrect syntax is detected (“parsing error”) all input

is ignored up until the next whitespace character.

Also note that any number can be entered in any format

(Hexadecimal, Decimal, Octal and binary) by adding the

corresponding prefix (‘0x’, ‘0’, ‘0b’). The only exception is

the ‘Send Frame’ command (

AT$SF) which expects a list of

hexadecimal digits without any prefix.

Return Codes

A successful command execution is indicated by sending

‘OK’. If a command returns a value (e.g. by querying a

Examples

Bold text is sent to AX−Sigfox.

AT$I=0

AXSEM AT Command Interface

Here, we execute command ‘I’ to query some general

information.

AT$SF=aabb1234

This sends a Sigfox frame containing { 0x00 : 0x11 : 0x22

: 0x33 : 0x44 }, then waits for a downlink response telegram,

which in this example contains { 0xAA : 0xBB : 0xCC :

0xDD }.

AT$CB=0011223344,1

RX=AA BB CC DD

AX-SIGFOX-API データシート(PDF) 11 Page - ON Semiconductor

AX-SIGFOX-API データシート(HTML) 11 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

データシートダウンロード