TriPle OuTPuT MOdel – MHF+28512T

±12 (auXiliarieS)

uniTS

ParaMeTer

COndiTiOnS

Min

TYP

MaX

Min

TYP

MaX

oUTpUT VolTAge

5.15

±11.52

±12.00

±12.48

V

eiTHer OuTPuT

—

—

1.5

0

±0.313

a

TOTal

—

—

1.5

—

—

0.625

eiTHer OuTPuT

—

—

7.5

—

±3.75

W

TOTal

—

—

7.5

—

—

7.5

OuTPuT riPPle

—

20

60

—

±30

±90

mV p-p

10 kHz - 2 MHz

—

—

90

—

—

±180

line regulaTiOn

—

25

75

—

±120

±240

mV

nO lOad TO Full

—

22

75

—

±120

±240

mV

eFFeCT on negATIVe

auXiliarY

—

—

—

—

—

750

mV

InpUT VolTAge

COnTinuOuS

16

28

48

—

—

—

V

nO lOad TO Full

—

—

80

—

—

—

V

inPuT CurrenT

nO lOad

—

30

45

—

—

—

ma

inHiBiTed

—

3

5

—

—

—

10 kHz - 10 MHz

—

20

50

—

—

—

ma p-p

eFFiCienCY

74

76

—

—

—

—

%

72

—

—

—

—

—

POWer diSSiPaTiOn

—

—

12

—

—

±12

W

SHOrT CirCuiT

—

—

25

—

—

25

ms

—

—

±850

—

—

±950

mV pk

ReCoVeRY

—

5

8

—

2

3

ms

—

—

±800

—

—

±800

mV pk

ReCoVeRY

—

—

5

—

—

5

ms

delaY

nO lOad and Full

—

10

25

—

10

±25

ms

—

—

500

—

—

±500

mV pk

notes

1. guaranteed by qualification test and/or analysis. not an in-line test.

a minimum of 4.80 volts to a maximum of 5.20 volts.

3. The sum of the 12 volt auxiliary output currents may not exceed 625 mA.

4. The sum of the auxiliary output power may not exceed 7.5 watts. Up to 5

watts (approximately 66%) of the total auxiliary output power is available

from either output providing the opposite output is simultaneously carrying

2.5 watts (approximately 33%) of the total auxiliary power.

5. load regulation for the +5 is specified at 0.0 to 1.5 A with the auxiliaries

both held at 3.75 W (313 mA). load regulation for the auxiliaries is

specified as both auxiliaries from 0.0 to 3.75 W (313 mA) at the same time

with the +5 held at 1.5 a.

6. Cross regulation only occurs between the two auxiliaries and is measured

on –aux. +5 is held constant at 1.0 A. Cross regulation is specified for two

conditions:

negative aux.= 3.76 W; positive aux.= 0.37 W to 3.76 W.

negative aux. = 0.37 W to 3.76 W; positive aux. = 3.76 W.

7. load fault = < 0.100 Ω.

8. indefinite short circuit protection not guaranteed above 125°C case.

10. Step transition time > 10 µs.

11. Step transition time 100 µs ±20%.

12. Measured on release from inhibit.

www.craneae.com/interpoint

Page 13 of 23

Crane Aerospace & Electronics Power Solutions

mHF+ Single, Dual and Triple DC-DC Converters

28 VOlT INPuT – 15 WaTT

MHF+ rev aB - 2014.10.02