LM3203

www.ti.com

SNVS355D – MAY 2005 – REVISED APRIL 2013

CAPACITOR SELECTION

The LM3203 is designed to be used with ceramic capacitors. Use a 10µF ceramic capacitor for the input and a

4.7µF ceramic capacitor for the output. Ceramic capacitors such as X5R, X7R and B are recommended for both

filters. These provide an optimal balance between small size, cost, reliability and performance for cell phones

and similar applications. Table 2 lists suggested capacitors and suppliers.

Model

Size (EIA)

Vendor

LMK212BJ475MG

2012 (0805)

Taiyo-Yuden

C2012X5R0J475K

2012 (0805)

TDK

C3216X5R1A106K

3216 (1206)

TDK

(1)

The DC bias characteristics of the capacitor must be considered when selecting case sizes. If smaller case size

such as 1608 (0603) is selected, the dc bias could reduce the cap value by as much as 40%, in addition to the

20% tolerances and 15% temperature coefficients. Request dc bias curves from manufacturer when making

selection.The device has been designed to be stable with output capacitance as low as 3

μF to account for

capacitor tolerances.This value includes dc bias reduction, manufacturing tolerences and temp coefficients.

The input filter capacitor supplies AC current drawn by the PFET switch of the LM3203 in the first part of each

cycle and reduces the voltage ripple imposed on the input power source. A 0.1µF capacitor is also recommended

voltage during transient load changes and reduces output voltage ripple. These capacitors must be selected with

sufficient capacitance and sufficiently low ESR (Equivalent Series Resistance) to perform these functions. The

ESR of the filter capacitors is generally a major factor in voltage ripple.

DSBGA PACKAGE ASSEMBLY AND USE

Use of the DSBGA package requires specialized board layout, precision mounting and careful re-flow

techniques, as detailed in TI Application Note 1112 (SNVA009). Refer to the section Surface Mount Technology

(SMD) Assembly Considerations. For best results in assembly, alignment ordinals on the PC board should be

used to facilitate placement of the device. The pad style used with DSBGA package must be the NSMD (non-

solder mask defined) type. This means that the solder-mask opening is larger than the pad size. This prevents a

lip that otherwise forms if the solder-mask and pad overlap, from holding the device off the surface of the board

and interfering with mounting. See Application Note 1112 (SNVA009) for specific instructions how to do this. The

10-Bump package used for the LM3203 has 300 micron solder balls and requires 10.82 mil pads for mounting on

the circuit board. The trace to each pad should enter the pad with a 90° entry angle to prevent debris from being

caught in deep corners. Initially, the trace to each pad should be 6-7 mil wide, for a section approximately 6 mil

long or longer, as a thermal relief. Then each trace should neck up or down to its optimal width. The important

criterion is symmetry. This ensures the solder bumps on the LM3203 re-flow evenly and that the device solders

level to the board. In particular, special attention must be paid to the pads for bumps B3, C3 and D3. Because

inadequate re-flow of these bumps.

The DSBGA package is optimized for the smallest possible size in applications with red or infrared opaque

cases. Because the DSBGA package lacks the plastic encapsulation characteristic of larger devices, it is

vulnerable to light. Backside metalization and/or epoxy coating, along with front-side shading by the printed

circuit board, reduce this sensitivity. However, the package has exposed die edges. In particular, DSBGA

devices are sensitive to light, in the red and infrared range, shining on the package’s exposed die edges.

Do not use or power-up the LM3203 while subjecting it to high intensity red or infrared light; otherwise degraded,

unpredictable or erratic operation may result. Examples of light sources with high red or infrared content include

the sun and halogen lamps. Place the device in a case opaque to red or infrared light.

Copyright © 2005–2013, Texas Instruments Incorporated

Submit Documentation Feedback

15

Product Folder Links: LM3203