74FST6800QG8 datasheet(2/5 Pages) IDT

2 / 5 page

INDUSTRIALTEMPERATURERANGE

IDT74FST6800

10-BIT BUS SWITCH WITH PRECHARGED OUTPUTS

Symbol

Description

Max

Unit

VTERM(2) Terminal Voltage with Respect to GND

–0.5 to +7

TSTG

Storage Temperature

–65 to +150

°C

IOUT

Maximum Continuous Channel Current

128

ABSOLUTE MAXIMUM RATINGS(1)

NOTES:

1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause

permanent damage to the device. This is a stress rating only and functional operation

of the device at these or any other conditions above those indicated in the operational

sections of this specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect reliability.

2. Vcc, Control, and Switch terminals.

Symbol

Parameter

Conditions(2)

Typ. Unit

CIN

Control Input Capacitance

CI/O

Switch Input/Output Capacitance

Switch Off

CAPACITANCE(1)

NOTES:

1. Capacitance is characterized but not tested.

2. TA = 25°C, f = 1MHz, VIN = 0V, VOUT = 0V.

Pin Names

I/O

Description

A1-10, B1-10

I/O

Buses A, B

Bus Switch Enable (Active LOW)

BIASV

BIAS Voltage

PIN DESCRIPTION

NOTE:

1. H = HIGH Voltage Level

L = LOW Voltage Level

FUNCTION TABLE(1)

B1-10

Description

LA1-10

Connect

BIASV

Precharge

Symbol

Parameter

Test Conditions(1)

Min.

Typ.(2)

Max.

Unit

VIH

Input HIGH Voltage

Guaranteed Logic HIGH for Control Inputs

—

VIL

Input LOW Voltage

Guaranteed Logic LOW for Control Inputs

—

0.8

IIH

Input HIGH Current

VCC = Max.

VI = VCC

——

±1

μA

IIL

Input LOW Current

VI = GND

—

±1

Precharge Output Current

VCC = Min., BIASV = 2.4V, VO = 0V

0.15

—

IOZH

High Impedance Output Current

VCC = Max.

VO = VCC

——

±1

μA

IOZL

(3-State Output Pins)

VO = GND

—

±1

IOS

Short Circuit Current

VCC = Min., VO = GND(3)

—

300

—

VIK

Clamp Diode Voltage

VCC = Min., IIN = –18mA

—

–0.7

–1.2

RON

Switch On Resistance(4)

VCC = 4.75V, VIN = 0.0V ION = 64mA

—

VCC = 4.75V, VIN = 2.4V ION = 15mA

—

IOFF

Input/Output Power Off Leakage

VCC = 0V, VIN or VO

≤ 4.5V

—

μA

ICC

Quiescent Power Supply Current

VCC = Max., VI = GND or VCC

—

0.1

μA

DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE

FollowingConditionsApplyUnlessOtherwiseSpecified:

Industrial: TA = –40°C to +85°C, VCC = 5.0V ± 5%, BIASV = 0 to VCC

NOTES:

1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.

2. Typical values are at VCC = 5.0V, +25°C ambient.

3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.

4. Measured by voltage drop between ports at indicated current through the switch.

74FST6800QG8 データシート(PDF) 2 Page - Integrated Device Technology

74FST6800QG8 データシート(HTML) 2 Page - Integrated Device Technology

Html Pages

1 2 3 4 5

データシートダウンロード

リンク URL

74FST6800QG8 データシート(PDF) 2 Page - Integrated Device Technology

74FST6800QG8 データシート(HTML) 2 Page - Integrated Device Technology

Html Pages

1 2 3 4 5

データシート ダウンロード

リンク URL

データシートダウンロード