ADA4817-2ACPZ-R2 datasheet(16/25 Pages) AD

16 / 25 page

ADA4817-1/ADA4817-2

Data Sheet

Rev. C | Page 16 of 25

Table 8. Power-Down Voltage Control

PD Pin

±5 V

+3 V, −2 V

Not active

>4 V

>2 V

Active

<2 V

<0 V

CAPACITIVE FEEDBACK

Due to package variations and pin to pin parasitics between the

single and the dual models, the ADA4817-2 has a little more

peaking then the ADA4817-1, especially at a gain of 2. The best

way to tame the peaking is to place a feedback capacitor across

the feedback resistor. Figure 46 shows the small signal frequency

response of the ADA4817-2 at a gain of 2 vs. CF. At first, no CF

was used to show the peaking, but then two other values of

0.5 pF and 1 pF were used to show how to reduce the peaking or

even eliminate it. As shown in Figure 46, if the power consumption

is a factor in the system, then using a larger feedback capacitor

is acceptable as long as a feedback capacitor is used across it to

control the peaking. However, if power consumption is not an

issue, a lower value feedback resistor, such as 200 Ω, does not

require any additional feedback capacitance to maintain flatness

and lower peaking.

–3

–6

–9

10M

100M

10G

FREQUENCY (Hz)

RF = 348Ω

G = 2

VS = 10V

VOUT = 100mV p-p

RL = 100Ω

CF = 1pF

CF = 0.5pF

NO CF

Figure 46. Small Signal Frequency Response vs. Feedback Capacitor

(ADA4817-2)

HIGHER FREQUENCY ATTENUATION

There is another package variation problem between the SOIC

and the LFCSP package. The SOIC package shows approximately

1 dB to 1.5 dB of additional peaking at a gain of 1. This is due to

the parasitic in the SOIC package, which is not recommended

for very high frequency parts that exceed 1 GHz. A good approach

to reducing the peaking is to place a resistor, RS, in series with

the noninverting input. This creates a first-order pole formed by

RS and CIN, the common-mode input capacitance.

Figure 47 shows the higher frequency attenuation, which

reduces the peaking but also reduces the −3 dB bandwidth.

–9

–6

–3

10M

100M

10G

FREQUENCY (Hz)

RS = 100Ω

RS = 75Ω

RS = 50Ω

RS = 0Ω

RL = 100Ω

VS = ±5V

VOUT = 0.1V p-p

G = 1

Figure 47. Small Signal Frequency Response for Various RS (SOIC)

As shown in Figure 47, the peaking dropped by almost 2 dB

when RS = 0 Ω to RS = 100 Ω, and in return, the −3 dB bandwidth

dropped from 1 GHz to 700 MHz. To maintain the −3 dB

bandwidth and to reduce peaking, an RLC circuit is recommended

instead of RS, as shown in Figure 48.

10nH

120Ω

2pF

Figure 48. RLC Circuit

The R in parallel to the series LC forms a notch that can be

shaped to compensate for the peaking produced by the amplifier.

The result is a smooth 1 GHz −3 dB bandwidth, 250 MHz 0.1 dB

flatness, and less than 1 dB of peaking. Place this circuit in the

path of the noninverting input when the ADA4817-1/ADA4817-2

are used at a gain of 1. The RLC values may need tweaking

depending on the source impedance and the flatness and

bandwidth required. Figure 49 shows the frequency response

after the RLC circuit is in place.

–9

–6

–3

10M

100M

10G

FREQUENCY (Hz)

RLC

NO RLC

RL = 100Ω

VS = 10V

VOUT = 100mV p-p

G = 1

Figure 49. Frequency Response with RLC Circuit

ADA4817-2ACPZ-R2 データシート(PDF) 16 Page - Analog Devices

ADA4817-2ACPZ-R2 データシート(HTML) 16 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

データシートダウンロード

リンク URL

ADA4817-2ACPZ-R2 データシート(PDF) 16 Page - Analog Devices

ADA4817-2ACPZ-R2 データシート(HTML) 16 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

データシート ダウンロード

リンク URL

データシートダウンロード