TPS62290DRVR datasheet(5/27 Pages) TI1

5 / 27 page

TPS62290, TPS62291, TPS62293

www.ti.com

SLVS764F – JUNE 2007 – REVISED JANUARY 2016

7.5 Electrical Characteristics

Over full operating ambient temperature range, typical values are at TA = 25°C. Unless otherwise noted, specifications apply

for condition VIN = EN = 3.6 V. External components CIN = 4.7 μF 0603, COUT = 10 μF 0603, L = 2.2 μH, refer to parameter

measurement information.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

SUPPLY

VIN

Input voltage

2.3

VIN 2.7 V to 6 V

1000

IOUT

Output current

VIN 2.5 V to 2.7 V

600

VIN 2.3 V to 2.5 V

300

IOUT = 0 mA, PFM mode enabled

(MODE = GND) device not switching,

μA

See (1)

Operating quiescent current

IOUT = 0 mA, switching with no load

(MODE = VIN) PWM operation,

3.8

VOUT = 1.8 V, VIN = 3 V

ISD

Shutdown current

EN = GND

0.1

μA

Falling

1.85

UVLO

Undervoltage lockout threshold

Rising

1.95

ENABLE, MODE

High level input voltage, EN,

2.3 V

≤ VIN ≤ 6 V

VIN

VIH

MODE

Low level input voltage, EN,

2.3 V

≤ VIN ≤ 6 V

0.4

VIL

MODE

IIN

Input bias current, EN, MODE

EN, MODE = GND or VIN

0.01

μA

POWER SWITCH

High side MOSFET on-resistance

240

480

RDS(on)

VIN = VGS = 3.6 V, TA = 25°C

Ω

Low side MOSFET on-resistance

185

380

Forward current limit MOSFET

ILIMF

VIN = VGS = 3.6 V

1.19

1.4

1.68

high-side and low side

Thermal shutdown

Increasing junction temperature

140

TSD

°C

Thermal shutdown hysteresis

Decreasing junction temperature

OSCILLATOR

fSW

Oscillator frequency

2.3 V

≤ VIN ≤ 6 V

2.0

2.25

2.5

MHz

OUTPUT

VOUT

Adjustable output voltage range

0.6

Vref

Reference voltage

600

MODE = VIN, PWM operation,

VFB(PWM)

Feedback voltage PWM mode

–1.5%

1.5%

2.3 V

≤ VIN ≤ 6 V, See

(2)

MODE = GND, device in PFM mode,

VFB(PFM)

Feedback voltage PFM mode

+1% voltage positioning active, See (1)

Load regulation

–0.5

%/A

Time from active EN to reach 95% of

500

tStart Up

Start-up time

μs

VOUT

tRamp

VOUT ramp-up time

Time to ramp from 5% to 95% of VOUT

250

μs

VIN = 3.6 V, VIN = VOUT = VSW, EN =

Ilkg

Leakage current into SW pin

GND,

0.1

μA

See (3)

(1)

In PFM mode, the internal reference voltage is set to typical 1.01 × Vref . See the parameter measurement information.

(2)

For VIN = VOUT + 1.0 V

(3)

In fixed output voltage versions, the internal resistor divider network is disconnected from FB pin.

Submit Documentation Feedback

Product Folder Links: TPS62290 TPS62291 TPS62293

TPS62290DRVR データシート(PDF) 5 Page - Texas Instruments

TPS62290DRVR データシート(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

データシートダウンロード

リンク URL

TPS62290DRVR データシート(PDF) 5 Page - Texas Instruments

TPS62290DRVR データシート(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

データシート ダウンロード

リンク URL

データシートダウンロード