HT46R46 datasheet(6/42 Pages) HOLTEK

6 / 42 page

HT46R46/HT46C46/HT46R47/HT46C47

Rev. 1.00

December 28, 2004

Functional Description

Execution Flow

The system clock for the microcontroller is derived from

either a crystal or an RC oscillator. The system clock is

internally divided into four non-overlapping clocks. One

instruction cycle consists of four system clock cycles.

Instruction fetching and execution are pipelined in such

a way that a fetch takes an instruction cycle while de-

coding and execution takes the next instruction cycle.

However, the pipelining scheme causes each instruc-

tion to effectively execute in a cycle. If an instruction

changes the program counter, two cycles are required to

complete the instruction.

Program Counter

- PC

The program counter (PC) controls the sequence in

which the instructions stored in program ROM are exe-

cuted and its contents specify full range of program

memory.

After accessing a program memory word to fetch an in-

struction code, the contents of the program counter are

incremented by one. The program counter then points to

the memory word containing the next instruction code.

When executing a jump instruction, conditional skip ex-

ecution, loading PCL register, subroutine call, initial re-

set, internal interrupt, external interrupt or return from

subroutine, the PC manipulates the program transfer by

loading the address corresponding to each instruction.

The conditional skip is activated by instructions. Once

the condition is met, the next instruction, fetched during

the current instruction execution, is discarded and a

dummy cycle replaces it to get the proper instruction.

Otherwise proceed with the next instruction.

The lower byte of the program counter (PCL) is a read-

able and writeable register (06H). Moving data into the

PCL performs a short jump. The destination will be

within 256 locations.

When a control transfer takes place, an additional

dummy cycle is required.

T 1

T 2

T 3

T 4

T 1

T 2

T 3

T 4

T 1

T 2

T 3

T 4

F e t c h I N S T ( P C )

E x e c u t e I N S T ( P C - 1 )

F e t c h I N S T ( P C + 1 )

E x e c u t e I N S T ( P C )

F e t c h I N S T ( P C + 2 )

E x e c u t e I N S T ( P C + 1 )

P C

P C + 1

P C + 2

S y s t e m C l o c k

O S C 2 ( R C o n l y )

P C

Execution Flow

Mode

Program Counter

*10

Initial Reset

00000000000

External Interrupt

00000000100

Timer/Event Counter Overflow

00000001000

A/D Converter Interrupt

00000001100

Skip

Program Counter+2

Loading PCL

*10

Jump, Call Branch

#10

Return from Subroutine

S10

Program Counter

Note:

*10~*0: Program counter bits

S10~S0: Stack register bits

#10~#0: Instruction code bits

@7~@0: PCL bits

For the HT46R47/HT46C47, the Program Counter is 11 bits wide, i.e. from *10~*0.

For the HT46R46/HT46C46, the Program Counter is 10 bits wide, the *10 the column in the table is not

applicable.

HT46R46 データシート(PDF) 6 Page - Holtek Semiconductor Inc

HT46R46 データシート(HTML) 6 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

データシートダウンロード

リンク URL

HT46R46 データシート(PDF) 6 Page - Holtek Semiconductor Inc

HT46R46 データシート(HTML) 6 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

データシート ダウンロード

リンク URL

データシートダウンロード