JS28F128P30T85 datasheet(49/102 Pages) INTEL

49 / 102 page

1-Gbit P30 Family

Datasheet

Intel StrataFlash® Embedded Memory (P30)

April 2005

Order Number: 306666, Revision: 001

9.1.2

Writes

To perform a write operation, both CE# and WE# are asserted while RST# and OE# are deasserted.

During a write operation, address and data are latched on the rising edge of WE# or CE#,

whichever occurs first. Table 20, “Command Bus Cycles” on page 50 shows the bus cycle

sequence for each of the supported device commands, while Table 21, “Command Codes and

Definitions” on page 51 describes each command. See Section 7.0, “AC Characteristics” on

page 33 for signal-timing details.

Note:

Write operations with invalid VCC and/or VPP voltages can produce spurious results and should not

be attempted.

9.1.3

Output Disable

When OE# is deasserted, device outputs DQ[15:0] are disabled and placed in a high-impedance

(High-Z) state, WAIT is also placed in High-Z.

9.1.4

Standby

When CE# is deasserted the device is deselected and placed in standby, substantially reducing

power consumption. In standby, the data outputs are placed in High-Z, independent of the level

placed on OE#. Standby current, ICCS, is the average current measured over any 5 ms time interval,

µs after CE# is deasserted. During standby, average current is measured over the same time

interval 5

µs after CE# is deasserted.

When the device is deselected (while CE# is deasserted) during a program or erase operation, it

continues to consume active power until the program or erase operation is completed.

9.1.5

Reset

As with any automated device, it is important to assert RST# when the system is reset. When the

system comes out of reset, the system processor attempts to read from the flash memory if it is the

system boot device. If a CPU reset occurs with no flash memory reset, improper CPU initialization

may occur because the flash memory may be providing status information rather than array data.

Flash memory devices from Intel allow proper CPU initialization following a system reset through

the use of the RST# input. RST# should be controlled by the same low-true reset signal that resets

the system CPU.

After initial power-up or reset, the device defaults to asynchronous Read Array, and the Status

drivers in High-Z. When RST# is asserted, the device shuts down the operation in progress, a

process which takes a minimum amount of time to complete. When RST# has been deasserted, the

device is reset to asynchronous Read Array state.

Note:

If RST# is asserted during a program or erase operation, the operation is terminated and the

memory contents at the aborted location (for a program) or block (for an erase) are no longer valid,

because the data may have been only partially written or erased.

When returning from a reset (RST# deasserted), a minimum wait is required before the initial read

access outputs valid data. Also, a minimum delay is required after a reset before a write cycle can

be initiated. After this wake-up interval passes, normal operation is restored. See Section 7.0, “AC

Characteristics” on page 33 for details about signal-timing.

JS28F128P30T85 データシート(PDF) 49 Page - Intel Corporation

JS28F128P30T85 データシート(HTML) 49 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード