DS198 LUXEON CZ Color Line Product Datasheet 20210826 ©2021 Lumileds Holding B.V. All rights reserved.

5

Electrical and Thermal Characteristics

Table 3 . Electrical and thermal characteristics for LUXEON CZ Color Line at 350mA, T

Color

Part numBEr

tyPICal tEmPEraturE

CoEFFICIEnt oF ForWard

tyPICal tHErmal

rEsIstanCE—JunCtIon

to soldEr Pad (°C/W)

mInImum

tyPICal maXImum

Far Red

L1CU-FRD1000000000

1.50

1.90

2.30

-1.7

3.5

Deep Red

L1CU-DRD1000000000

1.50

2.05

2.30

-1.7

3.5

Red

L1CU-RED1000000000

1.75

2.00

2.50

-1.6

3.5

Red-Orange

L1CU-RNG1000000000

1.75

2.05

2.50

-1.6

3.5

Amber

L1CU-AMB1000000000

1.75

2.05

2.50

-2.0

3.5

PC Amber

L1CU-PCA1000000000

2.50

2.75

3.50

-1.7

3.5

Mint

L1CU-MNT1000000000

2.50

2.75

3.50

-2.7

3.2

Lime

L1CU-LME1000000000

2.50

2.75

3.50

-2.7

3.2

Green

L1CU-GRN1000000000

2.50

3.05

3.50

-2.4

4.0

Cyan

L1CU-CYN1000000000

2.50

3.05

3.50

-2.4

4.0

Blue

L1CU-BLU1000000000

2.50

2.83

3.50

-2.6

4.0

Royal Blue

L1CU-RYL0000000000

2.50

2.75

3.50

-1.7

3.2

Violet

L1CU-VLT1000000000

2.50

2.83

3.50

-1.7

3.2

White

L1CU-xxx0000000000

2.50

2.75

3.50

-1.7

3.2

Notes for Table 3:

1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.

2. Measured between 25°C and 85°C.

Absolute Maximum Ratings

Table 4 . Absolute maximum ratings for LUXEON CZ Color Line .

ParamEtEr

dEEP rEd

Far rEd,

rEd, rEd-oranGE,

amBEr and PC amBEr

GrEEn

and Cyan

BluE

and royal BluE

mInt, lImE,

VIolEt

and WHItE

700mA

1050mA

1050mA

1050mA

1225mA

875mA

1300mA

1300mA

1300mA

1500mA

135°C

120°C

135°C

135°C

135°C

ESD Sensitivity

(ANSI/ESDA/JEDEC JS-001-2012)

Class 3B

LED Storage Temperature

-40°C to 135°C

Soldering Temperature

JEDEC 020c 260°C

Allowable Reflow Cycles

3

Reverse Voltage (V

LUXEON C LEDs are not designed to be driven in reverse bias

Notes for Table 4:

1. Proper current derating must be observed to maintain the junction temperature below the maximum allowable junction temperature.

2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple,” are acceptable if the following conditions are met:

– The frequency of the ripple current is 100Hz or higher

– The average current for each cycle does not exceed the maximum allowable DC forward current

– The maximum amplitude of the ripple does not exceed the maximum peak pulsed forward current

3. At 10% duty cycle with pulse width of 10ms.