DSPIC30F datasheet(25/220 Pages) MICROCHIP

25 / 220 page

 2004 Microchip Technology Inc.

Preliminary

DS70116C-page 23

dsPIC30F5011/5013

3.1.1

DATA ACCESS FROM PROGRAM

MEMORY USING TABLE

INSTRUCTIONS

This architecture fetches 24-bit wide program memory.

Consequently,

instructions

are

always

aligned.

However, as the architecture is modified Harvard, data

can also be present in program space.

There are two methods by which program space can

be accessed: via special table instructions, or through

the remapping of a 16K word program space page into

the upper half of data space (see Section 3.1.2). The

TBLRDL

and TBLWTL instructions offer a direct method

of reading or writing the LS Word of any address within

program space, without going through data space. The

TBLRDH

and TBLWTH instructions are the only method

whereby the upper 8 bits of a program space word can

be accessed as data.

The PC is incremented by two for each successive

24-bit program word. This allows program memory

addresses to directly map to data space addresses.

Program memory can thus be regarded as two 16-bit

word wide address spaces, residing side by side, each

with the same address range. TBLRDL and TBLWTL

access the space which contains the LS Data Word,

and TBLRDH and TBLWTH access the space which

contains the MS Data Byte.

Figure 3-2 shows how the EA is created for table oper-

ations and data space accesses (PSV = 1). Here,

P<23:0> refers to a program space word, whereas

D<15:0> refers to a data space word.

A set of table instructions are provided to move byte or

word sized data to and from program space.

TBLRDL:

Table Read Low

Word: Read the LS Word of the program address;

P<15:0> maps to D<15:0>.

Byte: Read one of the LS Bytes of the program

address;

P<7:0> maps to the destination byte when byte

select = 0;

P<15:8> maps to the destination byte when byte

select = 1.

TBLWTL:

Table Write Low (refer to Section 6.0

for details on Flash Programming)

TBLRDH:

Table Read High

Word: Read the MS Word of the program address;

P<23:16> maps to D<7:0>; D<15:8> will always

be = 0.

Byte: Read one of the MS Bytes of the program

address;

P<23:16> maps to the destination byte when

byte select = 0;

The destination byte will always be = 0 when

byte select = 1.

TBLWTH:

Table Write High (refer to Section 6.0

for details on Flash Programming)

FIGURE 3-3:

PROGRAM DATA TABLE ACCESS (LS WORD)

PC Address

0x000000

0x000002

0x000004

0x000006

00000000

Program Memory

‘Phantom’ Byte

(read as ‘0’)

TBLRDL.W

TBLRDL.B (Wn<0> = 1)

TBLRDL.B (Wn<0> = 0)

DSPIC30F データシート(PDF) 25 Page - Microchip Technology

DSPIC30F データシート(HTML) 25 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード