DSPIC30F datasheet(14/220 Pages) MICROCHIP

14 / 220 page

dsPIC30F5011/5013

DS70116C-page 12

Preliminary

 2004 Microchip Technology Inc.

2.2

Programmer’s Model

The programmer’s model is shown in Figure 2-1 and

consists of 16 x 16-bit working registers (W0 through

W15), 2 x 40-bit accumulators (AccA and AccB),

STATUS register (SR), Data Table Page register

(TBLPAG), Program Space Visibility Page register

(PSVPAG), DO and REPEAT registers (DOSTART,

DOEND, DCOUNT and RCOUNT) and Program

Counter (PC). The working registers can act as data,

address or offset registers. All registers are memory

mapped. W0 acts as the W register for file register

addressing.

Some of these registers have a shadow register asso-

ciated with each of them, as shown in Figure 2-1. The

shadow register is used as a temporary holding register

and can transfer its contents to or from its host register

upon the occurrence of an event. None of the shadow

registers are accessible directly. The following rules

apply for transfer of registers into and out of shadows.

• PUSH.S and POP.S

W0, W1, W2, W3, SR (DC, N, OV, Z and C bits

only) are transferred.

• DO instruction

DOSTART, DOEND, DCOUNT shadows are

pushed on loop start, and popped on loop end.

When a byte operation is performed on a working reg-

ister, only the Least Significant Byte of the target regis-

ter is affected. However, a benefit of memory mapped

working registers is that both the Least and Most Sig-

nificant Bytes can be manipulated through byte wide

data memory space accesses.

2.2.1

SOFTWARE STACK POINTER/

FRAME POINTER

The dsPIC® devices contain a software stack. W15 is

the dedicated software Stack Pointer (SP), and will be

automatically modified by exception processing and

subroutine calls and returns. However, W15 can be ref-

erenced by any instruction in the same manner as all

other W registers. This simplifies the reading, writing

and manipulation of the stack pointer (e.g., creating

stack frames).

W15 is initialized to 0x0800 during a Reset. The user

may reprogram the SP during initialization to any

location within data space.

W14 has been dedicated as a stack frame pointer as

defined by the LNK and ULNK instructions. However,

W14 can be referenced by any instruction in the same

manner as all other W registers.

2.2.2

STATUS REGISTER

The dsPIC core has a 16-bit STATUS register (SR), the

LS Byte of which is referred to as the SR Low byte

(SRL) and the MS Byte as the SR High byte (SRH).

See Figure 2-1 for SR layout.

SRL contains all the MCU ALU operation status flags

(including the Z bit), as well as the CPU Interrupt Prior-

ity Level status bits, IPL<2:0> and the Repeat Active

status bit, RA. During exception processing, SRL is

concatenated with the MS Byte of the PC to form a

complete word value which is then stacked.

The upper byte of the STATUS register contains the

DSP Adder/Subtracter status bits, the DO Loop Active

bit (DA) and the Digit Carry (DC) status bit.

2.2.3

PROGRAM COUNTER

The program counter is 23-bits wide; bit 0 is always

clear. Therefore, the PC can address up to 4M

instruction words.

Note:

In order to protect against misaligned

stack accesses, W15<0> is always clear.

DSPIC30F データシート(PDF) 14 Page - Microchip Technology

DSPIC30F データシート(HTML) 14 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード