L9963E datasheet(94/184 Pages) STMICROELECTRONICS

94 / 184 page

Operation

Skip condition

C9-C8

VCELL9_EN = 0

C10-C9

VCELL10_EN = 0

C11-C10

VCELL11_EN = 0

C12-C11

VCELL12_EN = 0

C13-C12

VCELL13_EN = 0

C14-C13

VCELL14_EN = 0

The step duration is not fixed, since it lasts TCYCLEADC, thus depending on the value programmed in the

ADC_FILTER_SOC or ADC_FILTER_CYCLE fields (refer to Table 38).

The following failures can be flagged during cell conversion step execution, thus causing Configuration

Override:

•

VCELLX_UV: if the voltage of the x-th cell is lower than the programmed UV threshold (VCELL_UV)

•

VCELLX_OV: if the voltage of the x-th cell is higher than the programmed OV threshold (VCELL_OV)

•

VSUM_OV: if summing all cells voltage the outcome is higher than the programmed OV threshold (VBAT_OV

(SUM))

•

VSUM_UV: if summing all cells voltage the outcome is lower than the programmed UV threshold (VBAT_UV

(SUM))

•

VCELLX_BAL_UV (maskable): if the voltage of the x-th cell is lower than the programmed balance UV

threshold (VCELL_UV + VCELL_BAL_UV_ Δ)

4.12.3.2

VBAT conversion

VBAT pin conversion is the second step of the voltage conversion routine. It is mandatory, meaning that it cannot

be excluded from routine execution, neither in On-Demand Conversions nor in Cyclic Conversions.

During this step, the voltage on VBAT pin will be converted.

The step duration is not fixed, since it lasts TCYCLEADC, thus depending on the value programmed in the

ADC_FILTER_SOC or ADC_FILTER_CYCLE fields (refer to Table 38).

The following failures can be flagged during VBAT conversion step execution, thus causing Configuration

Override:

•

VBATTCRIT_OV: if the voltage converted is higher than the VBAT_CRITICAL_OV_TH.

•

VBATTCRIT_UV: if the voltage converted is lower than the VBAT_CRITICAL_UV_TH.

4.12.3.3

GPIO conversion

GPIO conversion is the third step of the voltage conversion routine.

L9963E allows possible to provide either the absolute conversion or the ratiometric conversion with respect to

VTREF_MEAS, based on GPIOx dedicated R/W SPI register bits ratio_abs_x_sel.

This step is optional:

•

To include it in On-Demand Conversions, the GPIO_CONV bit must be set along with the SOC in the same

SPI frame.

•

To specify its periodicity in Cyclic Conversions, the NCYCLE_GPIO field must be programmed (refer to

Operations Periodicity).

During this step, all the GPIO configured as analog inputs will be converted.

Table 62. Operations performed during GPIO conversion step

Operation

Skip condition

GPIO1

Always

GPIO2

Always

GPIO3

GPIO3_CONFIG != 00

L9963E

Voltage conversion routine

DS13636 - Rev 12

page 94/184

L9963E データシート(PDF) 94 Page - STMicroelectronics

L9963E データシート(HTML) 94 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード