Page <2>

V1.0

16/08/22

Static Shielding Bag

Newark.com/multicomp-pro

Farnell.com/multicomp-pro

sg.element14.com/b/multicomp-pro

Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for 

the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change 

without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, 

any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make 

any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or 

where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its 

negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019.

Part Number Table

Description

Part Number

Static Shielding Bag, 127mm×203mm, PK100

013-0004

Item

Test Standard

Result

Friction Static

E1A541 Appendix C 

Avg.

Triboelectric NanocoIombs

Quartz +0.10 PTFE -0.09

Capacitance Release

E1A541 Voltage Dierence

<20V

Anti-erosion

FTMS 101C Method 3005

No visible spots

Tensile Strength

ASTM D882-91, Method A

MD 6530 psi TD 5800 psi

Tear Initiation

ASTM D1004 -94-Notched

MD 2.5 lbs./in TD 2.0 lbs

Puncture Resistance

ASTM D3420

>100 PSI

Tear Resistance

ASTM D882

>8 lbs./in

Burst Strength

FTMS 101 C Method 2065.1

50 psi Nominal

Heat Seal Temperature

-

250 - 375°F

Heat Seal Pressure

-

30-70 PSI

Heat Seal Strength

(D1876-93) Vertrod bar sealer/heat

>12 lbs/in width (room temperature)

Breaking Elongation Rate

ASTM D882-91 Method A

MD 80% TD 85%

Appearance

GB/96-04-10

No delamination, burst seal, wrinkle, warp, 

break, foreign particle adherence, air bubble 

beyond sealing Ø≤3mm

Test Conclusion

The shielding bag is tested accordance with the relevant test standard & requirements.

Test Item:

Test Method:

Measured Equipment(s): MDL:

Lead (Pb)

IEC 62321:2008 Ed.1 Sec.8

ICP-OES

2mg/kg

Cadmium (Cd)

IEC 62321:2008 Ed.1 Sec.8

ICP-OES

2mg/kg

Mercury (Hg)

IEC 62321:2008 Ed.1 Sec.7

ICP-OES

2mg/kg

Hexavalent Chromium (Cr(VI))

IEC 62321:2008 Ed.1 Annex C UV-Vis

2mg/kg

Polybrominated Biphenyls (PBBs)

IEC 62321:2008 Ed.1 Annex A GC-MS

5mg/kg

Polybrominated Diphenyl Ethers (PBDEs) IEC 62321:2008 Ed.1 Annex A GC-MS

5mg/kg