 |
データシートサーチシステム |
|
|
データシートサーチシステム |
|
ST10F280 データシート(PDF) 156 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST10F280 データシート(HTML) 156 Page - STMicroelectronics |
|
|
156 / 186 page  ST10F280 156/186 Notes: 1. ST10F280 pins are equipped with low-noise output drivers which significantly improve the device’s EMI performance. These low-noise drivers deliver their maximum current only until the respective target output level is reached. After this, the output current is reduced. This results in increased impedance of the driver, which attenuates electrical noise from the connected PCB tracks. The current specified in column “Test Conditions” is delivered in any cases. 2. This specification is not valid for outputs which are switched to open drain mode. In this case the respective output will float and the voltage results from the external circuitry. 3. Partially tested, guaranteed by design characterization. 4. Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin exceeds the specified range (i.e. VOV > VDD+0.5V or VOV <0.5V). The absolute sum of input overload currents on all port pins may not exceed 50mA. The supply voltage must remain within the specified limits. VOH CC Output high voltage (PORT0, PORT1, Port4, ALE, RD, WR, BHE, CLKOUT, RSTOUT) 1 IOH = -500µA IOH = -2.4mA 0.9 VDD 2.4 – – V VOH1 CC Output high voltage (all other outputs) 1/2 IOH = – 250µA IOH = – 1.6mA 0.9 VDD 2.4 – – V V I OZ1 CC Input leakage current (Port 5, XPort 10) 0V < VIN < VDD – 0.2 µA I OZ2 CC Input leakage current (all other) 0V < VIN < VDD –1 µA I OV SR Overload current 3/4 –5 mA RRST CC RSTIN pull-up resistor 3 – 50 250 k Ω IRWH Read / Write inactive current 5/6 VOUT = 2.4V – -40 µA IRWL Read / Write active current 5/7 VOUT = VOLmax -500 – µA IALEL ALE inactive current 5/6 VOUT = VOLmax 40 – µA IALEH ALE active current 5/7 VOUT = 2.4V – 500 µA IP6H Port 6 inactive current 5/6 VOUT = 2.4V – -40 µA IP6L Port 6 active current 5/7 VOUT = VOL1max -500 – µA IP0H PORT0 configuration current 5/6 VIN = VIHmin – -10 µA IP0L 5/7 VIN = VILmax -100 – µA I IL CC XTAL1 input current 0V < VIN < VDD –20 µA CIO CC Pin capacitance (digital inputs / outputs) 3/5 f = 1MHz, TA = 25°C –10 pF ICC Power supply current 8 RSTIN = VIH1 fCPU in [MHz] – 30 + 3.3 x fCPU mA IID Idle mode supply current 9 RSTIN = VIH1 fCPU in [MHz] – 20 + fCPU mA IPD Power-down mode supply current 10 VDD = 5.5V TA = 55°C – 200 µA Symbol Parameter Test Conditions Min. Max. Unit |
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか？ [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Japanese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
