| データシートサーチシステム |
|
MCP9804-E/MS データシート(PDF) 11 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP9804-E/MS データシート(HTML) 11 Page - Microchip Technology |
|
11 / 54 page ![]() © 2009 Microchip Technology Inc. DS22203A-page 11 MCP9804 3.0 PIN DESCRIPTION The descriptions of the pins are listed in Table 3-1. 3.1 Address Pins (A0, A1, A2) These pins are device address input pins. The address pins correspond to the Least Significant bits (LSb) of address bits. The Most Significant bits (MSb) (A6, A5, A4, A3). This is shown in Table 3-2. 3.2 Ground Pin (GND) The GND pin is the system ground pin. 3.3 Serial Data Line (SDA) SDA is a bidirectional input/output pin, used to serially transmit data to/from the host controller. This pin requires a pull-up resistor. (See Section 4.0). 3.4 Serial Clock Line (SCL) The SCL is a clock input pin. All communication and timing is relative to the signal on this pin. The clock is generated by the host or master controller on the bus. (See Section 4.0). 3.5 Temperature Alert, Open-Drain Output (Alert) The MCP9804 temperature alert output pin is an open-drain output. The device outputs a signal when the ambient temperature goes beyond the user-programmed temperature limit. (See Section 5.2.3). 3.6 Power Pin (VDD) VDD is the power pin. The operating voltage range, as specified in the DC electrical specification table, is applied on this pin. 3.7 Exposed Thermal Pad (EP) There is an internal electrical connection between the Exposed Thermal Pad (EP) and the GND pin. The EP may be connected to the system ground on the Printed Circuit Board (PCB). TABLE 3-1: PIN FUNCTION TABLE DFN MSOP Symbol Pin Function 1 1 SDA Serial Data Line 2 2 SCL Serial Clock Line 3 3 Alert Temperature Alert Output 4 4 GND Ground 5 5 A2 Slave Address 6 6 A1 Slave Address 7 7 A0 Slave Address 88 VDD Power Pin 9 — EP Exposed Thermal Pad (EP); must be connected to GND. TABLE 3-2: MCP9804 ADDRESS BYTE Device Address Code Slave Address A6 A5 A4 A3 A2 A1 A0 MCP9804 0 0 1 1 X(1) XX MCP9804(2) 10 01 X X X Note 1: User-selectable address is shown by X. A2, A1 and A0 must match the corresponding device pin configuration. 2: Contact Factory for this Address Code. |
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |