| データシートサーチシステム |
|
TC58FVT641 データシート(PDF) 16 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TC58FVT641 データシート(HTML) 16 Page - Toshiba Semiconductor |
|
16 / 53 page ![]() TC58FVT641/B641FT/XB-70,-10 2001-09-06 16/53 HARDWARE SEQUENCE FLAGS The TC58FVT641/B641 has a Hardware Sequence flag which allows the device status to be determined during an auto mode operation. The output data is read out using the same timing as that used when CE = OE = VIL in Read Mode. The BY / RY output can be either High or Low. The device re-enters Read Mode automatically after an auto mode operation has been completed successfully. The Hardware Sequence flag is read to determine the device status and the result of the operation is verified by comparing the read-out data with the original data. STATUS DQ7 DQ6 DQ5 DQ3 DQ2 BY / RY Auto Programming 7 DQ Toggle 0 0 1 0 Read in Program Suspend (1) Data Data Data Data Data High-Z Selected (2) 0 Toggle 0 0 Toggle 0 Erase Hold Time Not-selected (3) 0 Toggle 0 0 1 0 Selected 0 Toggle 0 1 Toggle 0 In Auto Erase Auto Erase Not-selected 0 Toggle 0 1 1 0 Selected 1 1 0 0 Toggle High-Z Read Not-selected Data Data Data Data Data High-Z Selected 7 DQ Toggle 0 0 Toggle 0 In Progress In Erase Suspend Programming Not-selected 7 DQ Toggle 0 0 1 0 Auto Programming 7 DQ Toggle 1 0 1 0 Auto Erase 0 Toggle 1 1 NA 0 Time Limit Exceeded Programming in Erase Suspend 7 DQ Toggle 1 0 NA 0 Notes:DQ outputs cell data and BY / RY goes High-Impedence when the operation has been completed. DQ0 and DQ1 pins are reserved for future use. 0 is output on DQ0, DQ1 and DQ4. (1) Data output from an address to which Write is being performed is undefined. (2) Output when the block address selected for Auto Block Erase is specified and data is read from there. During Auto Chip Erase, all blocks are selected. (3) Output when a block address not selected for Auto Block Erase of same bank as selected block is specified and data is read from there. DQ7 ( polling) During an Auto-Program or auto-erase operation, the device status can be determined using the data polling function. DATA polling begins on the rising edge of WE in the last bus cycle. In an Auto-Program operation, DQ7 outputs inverted data during the programming operation and outputs actual data after programming has finished. In an auto-erase operation, DQ7 outputs 0 during the Erase operation and outputs 1 when the Erase operation has finished. If an Auto-Program or auto-erase operation fails, DQ7 simply outputs the data. When the operation has finished, the address latch is reset. Data polling is asynchronous with the OE signal. DATA |
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |