| データシートサーチシステム |
|
RT8205CGQW データシート(PDF) 8 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT8205CGQW データシート(HTML) 8 Page - Richtek Technology Corporation |
|
8 / 28 page ![]() RT8205A/B/C 8 DS8205A/B/C-06 July 2012 www.richtek.com © Copyright 2012 Richtek Technology Corporation. All rights reserved. is a registered trademark of Richtek Technology Corporation. GND [Pin 15 (RT8205A), Exposed Pad (25)] Analog Ground for SMPS controller. The exposed pad must be soldered to a large PCB and connected to GND for maximum power dissipation. PGND (Pin 15) (RT8205B/C) Power Ground for SMPS controller. Connect PGND externally to the underside of the exposed pad. VIN (Pin 16) High Voltage Power Supply Input for 5V/3.3V LDO and Feed-forward ON-Time circuitry. VREG5 (Pin 17) 5V Linear Regulator Output.VREG5 is also the supply voltage for the low-side MOSFET driver and analog supply voltage for the device. NC (Pin 18) (RT8205A) No Internal Connection. LG1_CP (Pin 18) (RT8205B) Alternative LGATE1 Output for 14V charge pump. SECFB (Pin 18) (RT8205C) The SECFB is used to monitor the optional external 14V charge pump. Connect a resistive voltage-divider from 14V charge pump output to GND to detect the output. If SECFB drops below the threshold voltage, LGATE1 turns on for 300ns (typ.). This will refresh the external charge pump driven by LGATE1 without over-discharging the output voltage. LGATE1 (Pin 19) SMPS1 Synchronous-Rectifier Gate-Drive Output. LGATE1 swings between GND and VREG5. PHASE1 (Pin 20) Inductor Connection for SMPS1. PHASE1 is the internal lower supply rail for the UGATE1 high-side gate driver. PHASE1 is also the current-sense input for the SMPS1. UGATE1 (Pin 21) High-Side MOSFET Floating Gate-Driver Output for SMPS1. UGATE1 swings between PHASE1 and BOOT1. BOOT1 (Pin 22) Boost Flying Capacitor Connection for SMPS1. Connect to an external capacitor according to the typical application circuits. PGOOD (Pin 23) Power Good Output for channel 1 and channel 2. (Logical AND) VOUT1 (Pin 24) SMPS1 Output Voltage-Sense Input. Connect to the SMPS1 output. VOUT1 is an input to the on-time one- shot circuit. It also serves as the SMPS1 feedback input in fixed-voltage mode. |
|
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |