STV9118 datasheet(22/46 Pages) STMICROELECTRONICS

22 / 46 page

STV9118

22/46

Note 44: With exception of

HDUTY and BREF adjustments data that can take effect instantaneously if switches

HDutySyncV and B+SyncV are at 0 respectively.

Note 45: In Read Mode, the device always outputs data of the status register, regardless of sub address previously

selected.

Note 46: The TV, TH, TVM and THM bits are for testing purposes and must be kept at 0 by application.

Description of I2C Bus switches and flags

Write-to bits

Sad00/D7 - HDutySyncV

Synchronization of internal application of Hori-

zontal Duty cycle data, buffered in I2C Bus latch,

with internal discharge of Vertical oscillator

0: Asynchronous mode, new data applied

with ACK bit of I2C Bus transfer on this sub

address

1: Synchronous mode

Sad02/D7 - HMoiré

Horizontal Moiré characteristics

0: Adapted to an architecture with EHT gener-

ated in deflection section

1: Adapted to an architecture with separated

deflection and EHT sections

Sad03/D7 - B+SyncV

Same as HDutySyncV, applicable for B+ refer-

ence data

Sad07/D7 - BOutPh

Phase of start of B+ drive signal on BOut pin

0: Just after horizontal flyback pulse

1: With one of edges of line drive signal on

HOut pin, selected by BOHEdge bit

Sad08/D7 - EWTrHFr

Tracking of all corrections contained in wave-

form on pin EWOut with Horizontal Frequency

0: Not active

1: Active

Sad15/D7 - VDyCorPol

Polarity of Vertical Dynamic Correction wave-

form (parabola)

0: Concave (minimum in the middle of the pa-

rabola)

1: Convex (maximum in the middle of the pa-

rabola)

Sad16/D0 - HLockEn

Enable of output of Horizontal PLL1 Lock/unlock

status signal on pin HLckVBk

0: Disabled, vertical blanking only on the pin

HLckVBk

1: Enabled

Reserved

PARAL

(Parallelogram correction)

000

Reserved

VDyCorPol

0: ”

∪"

VDC-AMP

(Vertical dynamic correction amplitude)

000

XRayReset

0: No effect

1: Reset

VSyncAuto

1: On

VSyncSel

0:Comp

1:Sep

SDetReset

0: No effect

1: Reset

HMoiMode

0: Internal

1: External

PLL1Pump

1: Fast

0: Slow

PLL1InhEn

1: On

HLockEn

1: On

0: Off

(46)

0: Off(46)

TVM

0: Off(46)

THM

0: Off(46)

BOHEdge

0: Falling

HBOutEn

0: Disable

VOutEn

0: Disable

BlankMode

1: Perm.

READ MODE (SLAVE ADDRESS = 8D)

(45)

HLock

0: Locked

1: Not locked

VLock

0: Locked

1: Not lock.

XRayAlarm

1: On

0: Off

Polarity detection

Sync detection

HVPol

1: Negative

VPol

1: Negative

VExtrDet

0: Not det.

HVDet

0: Not det.

VDet

0: Not det.

Sad

STV9118 データシート(PDF) 22 Page - STMicroelectronics

STV9118 データシート(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

データシートダウンロード

リンク URL

STV9118 データシート(PDF) 22 Page - STMicroelectronics

STV9118 データシート(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

データシート ダウンロード

リンク URL

データシートダウンロード