LTM4619EVPBF datasheet(13/24 Pages) LINER

13 / 24 page

LTM4619

4619f

Multiphase Operation

Multiphase operation with multiple LTM4619 devices in

parallel will lower the effective input RMS ripple current

as well as the output ripple current due to the interleaving

operation of the regulators. Figure 5 provides a ratio of

input RMS ripple current to DC load current as a function

of duty cycle and the number of paralleled phases. Choose

the corresponding duty factor and the number of phases

to get the correct ripple current value. For example, the

2-phase parallel for one LTM4619 design provides 8A

at 2.5V output from a 12V input. The duty cycle is DC =

2.5V/12V = 0.21. The 2-phase curve has a ratio of ~0.25

for a duty cycle of 0.21. This 0.25 ratio of RMS ripple cur-

rent to a DC load current of 8A equals ~2A of input RMS

ripple current for the external input capacitors.

The effective output ripple current is lowered with mul-

tiphase operations as well. Figure 6 provides a ratio of

peak-to-peak output ripple current to the normalized

output ripple current as a function of duty factor and the

number of paralleled phases. Choose the corresponding

duty factor and the number of phases to get the correct

output ripple current ratio value. If a 2-phase operation

is chosen at 12VIN to 2.5VOUT with a duty factor of 21%,

then 0.6 is the ratio of the normalized output ripple current

to inductor ripple DIr at the zero duty factor. This leads

to ~1.3A of the effective output ripple current

ΔIL if the

DIr is at 2.2A. Refer to Application Note 77 for a detailed

explanation of the output ripple current reduction as a

function of paralleled phases.

The output voltage ripple has two components that are

related to the amount of bulk capacitance and effective

series resistance (ESR) of the output bulk capacitance.

Therefore, the output voltage ripple can be calculated with

the known effective output ripple current. The equation:

ΔVOUT(P-P) ≈ ΔIL/(8 • f • N • COUT) + ESR • ΔIL

where f is frequency and N is the number of parallel

phases.

APPLICATIONS INFORMATION

RUN Pin

The RUN pins can be used to enable or sequence the

particular regulator channel. The RUN pins have their

own internal 0.5μA current source to pull up the pin to

1.2V, and then the current increases to 4.5μA above 1.2V.

Careful consideration is needed to assure that board

contamination or residue does not load down the 0.5μA

pull-up current. Otherwise active control to these pins can

be used to activate the regulators. A voltage divider can

be used from VIN to set an enable point that can be used

as a UVLO feature for the regulator. The resistor divider

needs to be low enough resistance to swamp out the pull-

up current sources and not enable the device when not

attended. See the Simpliﬁed Block Diagram.

Power Good

The PGOOD pin is connected to an open drain of an internal

N-channel MOSFET. The MOSFET turns on and pulls the

PGOOD pin low when either VFB pin voltage is not within

±7.5% of the 0.8V reference voltage. The PGOOD pin is

also pulled low when either RUN pin is below 1.2V or when

the LTM4619 is in the soft-start or tracking phase. When

the VFB pin voltage is within the ±7.5% requirement, the

MOSFET is turned off and the pin is allowed to be pulled

up by an external resistor to a source of up to 6V. The

PGOOD pin will ﬂag power good immediately when both

VFB pins are within the ±7.5% window. However, there is

an internal 17μs power bad mask when either VFB goes

out of the ±7.5% window.

LTM4619EVPBF データシート(PDF) 13 Page - Linear Technology

LTM4619EVPBF データシート(HTML) 13 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

データシートダウンロード