| データシートサーチシステム |
|
GS9025ACTME3 データシート(PDF) 4 Page - Gennum Corporation |
|
|
|||||||||||||||||||||||||||||
GS9025ACTME3 データシート(HTML) 4 Page - Gennum Corporation |
|
4 / 18 page ![]() GENNUM CORPORATION 522 - 75 - 05 4 of 18 Fig. 1 Test Setup for Figures 6 - 13 SDO Mute Time 0.5 1 2 µs 6 7 SDO to SCO Synchronization -200 0 200 ps 7 SDO, SCO Output Signal Swing 75 Ω DC load 600 800 1000 mV p-p 1 SDO, SCO Rise & Fall times 20%-80% 200 300 400 ps 7 SDI/SDI Input Resistance - 10 - k Ω 86 SDI/SDI Input Capacitance - 1.0 - pF 8 6 Carrier Detect Response Time Carrier Applied, - 3 - µs 8, 9 6 Carrier Removed, - 30 - NOTES 1. TYPICAL - measured on CB9025A board. 2. Characterized 6 sigma rms. 3. IJT measured with sinusoidal modulation beyond Loop Bandwidth (at 6.5MHz). 4. Synchronous switching refers to switching the input data from one source to another source which is at the same data rate (ie. line 10 switching for component NTSC). 5. Asynchronous switching refers to switching the input data from one source to another source which is at a different data rate. 6. SDO Mute Time refers to the response of the SDO outputs from valid re-clocked input data to mute mode when the input signal is removed. 7. Using the DDI input, A/D=0. 8. Using the SDI input, A/D=1. 9. Carrier detect response time refers to the response of the SSI/CD output from a logic high to logic low state when the input signal is removed or its amplitude drops below the threshold set by the CD_ADJ PIN. SSI/CD PIN loading CL<50pF, RL = open cct. TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1,2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. AC ELECTRICAL CHARACTERISTICS (Continued) VCC = 5.0V, VEE = 0V, TA = 0° to 70°C unless otherwise stated, RLF = 1.8k, CLF1 = 15nF, CLF2 = 3.3pF PARAMETER CONDITIONS MIN TYPICAL 1 MAX UNITS NOTES TEST LEVEL CB9025A BOARD GS9028 CABLE DRIVER TEKTRONIX GigaBERT 1400 ANALYZER TEKTRONIX GigaBERT 1400 TRANSMITTER BELDEN 8281 CABLE DATA DATA CLOCK TRIGGER |
|
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |