ATSAMB11XR datasheet(77/87 Pages) MICROCHIP

77 / 87 page

A user's manual for the finished product should include the following statement:

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy, and if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

•

Consult the dealer or an experienced radio/TV technician for help

Additional information on labeling and user information requirements for Part 15 devices can be found in

KDB Publication 784748, which is available at the FCC Office of Engineering and Technology (OET)

Laboratory Division Knowledge Database (KDB) https://apps.fcc.gov/oetcf/kdb/index.cfm

16.1.2

RF Exposure

All transmitters regulated by FCC must comply with RF exposure requirements. KDB 447498 General RF

Exposure Guidance provides guidance in determining whether proposed or existing transmitting facilities,

operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by

the Federal Communications Commission (FCC).

From the FCC Grant: Output power is conducted.

Module is approved for use in mixed mobile-device and portable-device exposure host platforms. The

antenna(s) used with this transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

16.1.3

Helpful Web Sites

Federal Communications Commission (FCC): http://www.fcc.gov

FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB):

https://apps.fcc.gov/oetcf/kdb/index.cfm

16.2

Canada

The ATSAMB11-ZR210CA module has been certified for use in Canada under Innovation, Science and

Economic Development Canada (ISED, formerly Industry Canada) Radio Standards Procedure (RSP)

RSP-100, Radio Standards Specification (RSS) RSS-Gen and RSS-247. Modular approval permits the

installation of a module in a host device without the need to recertify the device.

16.2.1

Labeling and User Information Requirements

Labeling Requirements (from RSP-100 Issue 11, Section 3): The host product shall be properly labeled to

identify the module within the host device.

Due to limited size of the ATSAMB11-ZR210CA (7.503 mm x10.541 mm), the Innovation, Science and

Economic Development Canada certification number is not displayed on the module. Therefore, the host

device must be labeled to display the Innovation, Science and Economic Development Canada

ATSAMB11XR/ZR

Datasheet Preliminary

DS70005342A-page 77

ATSAMB11XR データシート(PDF) 77 Page - Microchip Technology

ATSAMB11XR データシート(HTML) 77 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87

データシートダウンロード