GD25LB128DSJS datasheet(11/75 Pages) GIGADEVICE

11 / 75 page

1.8V Uniform Sector

Dual and Quad Serial Flash

GD25LB128D

6. STATUS REGISTER

S15

S14

S13

S12

S11

S10

SUS1

CMP

LB3

LB2

LB1

SUS2

SRP1

SRP0

BP4

BP3

BP2

BP1

BP0

WEL

WIP

The status and control bits of the Status Register are as follows:

WIP bit.

The Write in Progress (WIP) bit indicates whether the memory is busy in program/erase/write status register progress.

When WIP bit sets to 1, means the device is busy in program/erase/write status register progress, when WIP bit sets 0,

means the device is not in program/erase/write status register progress.

WEL bit.

The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch. When set to 1 the internal

Write Enable Latch is set, when set to 0 the internal Write Enable Latch is reset and no Write Status Register, Program or

Erase command is accepted.

BP4, BP3, BP2, BP1, BP0 bits.

The Block Protect (BP4, BP3, BP2, BP1, and BP0) bits are non-volatile. They define the size of the area to be software

protected against Program and Erase commands. These bits are written with the Write Status Register (WRSR) command.

When the Block Protect (BP4, BP3, BP2, BP1, BP0) bits are set to 1, the relevant memory area (as defined in

Table1).becomes protected against Page Program (PP), Sector Erase (SE) and Block Erase (BE) commands. The Chip

Erase (CE) command is executed, if the Block Protect (BP2, BP1, and BP0) bits are 0 and CMP=0 or the Block Protect

(BP2, BP1, and BP0) bits are 1 and CMP=1.

SRP1, SRP0 bits.

The Status Register Protect (SRP1 and SRP0) bits are non-volatile Read/Write bits in the status register. The SRP bits

control the method of write protection: software protection, power supply lock-down or one time programmable protection.

SRP1

SRP0

Status Register

Description

Software Protected

The Status Register can be written to after a Write Enable

command, WEL=1.(Default)

Power Supply Lock-Down(1)(2)

Status Register is protected and cannot be written to again until

the next Power-Down, Power-Up cycle.

One Time Program(2)

Status Register is permanently protected and cannot be written to.

NOTE:

1. When SRP1, SRP0= (1, 0), a Power-Down, Power-Up cycle will change SRP1, SRP0 to (0, 0) state.

2. This feature is available on special order. Please contact GigaDevice for details.

QE bit.

The Quad Enable (QE) bit is a non-volatile read only bit which allows Quad operation. The default value of QE bit is

1, and it cannot be changed so that the Quad IO2 and IO3 pins are enabled all the time.

LB3, LB2, LB1 bits.

The LB3, LB2, LB1 bits are non-volatile One Time Program (OTP) bits in Status Register (S13-S11) that provide the

write protect control and status to the Security Registers. The default state of LB3-LB1 are 0, the security registers are

unlocked. The LB3-LB1 bits can be set to 1 individually using the Write Register instruction. The LB3-LB1 bits are One Time

GD25LB128DSJS データシート(PDF) 11 Page - GigaDevice Semiconductor (Beijing) Inc.

GD25LB128DSJS データシート(HTML) 11 Page - GigaDevice Semiconductor (Beijing) Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

データシートダウンロード