AM29BDD160G datasheet(77/79 Pages) AMD

77 / 79 page

June 7, 2006

Am29BDD160G

REVISION SUMMARY

Revision B (September 30, 2002)

Initial public release.

Revision B+1 (October 7, 2002)

Distinctive Characteristics

Changed maximum power consumption on burst

mode read, program/erase operations, and standby

mode.

Burst Mode Read table

Changed t

CES specification from 7, 8, and 9 ns to 4, 5,

and 6 ns, respectively.

DC Characteristics table

Deleted I

CC2 specification. Changed ICCB OE# test

condition from V

IH to VIL. Added 1 MHz test condition

to I

CC1; changed OE# test condition from VIH to VIL.

Changed I

CC3 and ICC4 maximum values and added

typical values. Changed maximum values for I

CC5,

CC7, and ICC8. Added Note 4 to table.

AC Characteristics

Erase and Program Operations table: Replaced TBDs

for t

AH and tWP with values.

Erase and Programming Performance table

Replaced TBDs and existing typical and maximum val-

ues with new values.

Revision B+2 (October 14, 2002)

Distinctive Characteristics, DC Characteristics

Changed V

CC CMOS standby current to 30 mA max.

Absolute Maximum Ratings

Changed maximum rating for V

CC to 3.0 V.

Revision B+3 (November 22, 2002)

Product Selector Guide

Added availability note. Changed minimum initial clock

delay and maximum CE# access time on 54D, 65D,

64C, and 65A speeds. Changed maximum OE# ac-

cess time on 65A and 90A speeds.

Ordering Information

Added availability note.

See Table 8 , Burst Initial Access Delay

Deleted definitions and settings columns and added

initial burst access columns.

Figure 3, Initial Burst Delay Control

Modified drawing: Deleted arrows connecting ad-

dress/data cycles. Deleted setting callouts. Changed

number of delay cycles callouts. Moved start of Valid

Address cycle.

Falling CLK Edge Output and Two-CLK Data Hold

Deleted figure.

See Table 9 , Configuration Register Definitions

Modified descriptions for CR3–CR10.

See Table 16 , CFI Device Geometry Definition

Modified description of data at address 2Ch (x32

mode); added data 0003h.

DC Characteristics

Added maximum ICC6 specification.

AC Characteristics

Asynchronous Read Operations: Changed tCE specifi-

cations for 54D, 65D, 64C, and 65A speed options.

Changed tDF specifications for 65A and 90A speed op-

tions.

Revision B+4 (April 8, 2003)

Distinctive Characteristics

Corrected typo in Single power supply operation.

Corrected typo in Performance characteristics.

Product Selector Guide

Updated Max Burst Access Delay for the 54D, 65D,

64C, and 80C speed options.

Global

Removed references to interleaving operations

throughout datasheet.

Table 6. 16-Bit and 32-Bit Linear and Interleaved

Burst Data Order

Removed 2nd row for “Four Interleaved Data Trans-

fers” and “Eight Interleaved Data Transfers”.

Continuous Burst Read Operations, Figure 3. and

Figure 4. Wait Function During Continuous Burst

Reads at Wordline Boundary, Figure 5. and Figure

6. Odd/Even Starting address Continuous Burst

Mode Alignment

Removed from datasheet.

Table 9. Configuration Register Definitions

Added “Reserved” references to table.

Sector Protection

Added Sector and Sector Group section.

AM29BDD160G データシート(PDF) 77 Page - Advanced Micro Devices

AM29BDD160G データシート(HTML) 77 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

データシートダウンロード