STM32G071C8 datasheet(25/133 Pages) STMICROELECTRONICS

25 / 133 page

DS12232 Rev 3

25/133

STM32G071x8/xB

Functional overview

A register in the EXTI controller latches every event even in Stop mode, which allows the

software to identify the origin of the processor's wake-up from Stop mode or, to identify the

GPIO and the edge event having caused an interrupt.

3.14

Analog-to-digital converter (ADC)

A native 12-bit analog-to-digital converter is embedded into STM32G071x8/xB devices. It

can be extended to 16-bit resolution through hardware oversampling. The ADC has up to 16

external channels and 3 internal channels (temperature sensor, voltage reference, VBAT

monitoring). It performs conversions in single-shot or scan mode. In scan mode, automatic

conversion is performed on a selected group of analog inputs.

The ADC frequency is independent from the CPU frequency, allowing maximum sampling

rate of ~2 MSps even with a low CPU speed. An auto-shutdown function guarantees that

the ADC is powered off except during the active conversion phase.

The ADC can be served by the DMA controller. It can operate in the whole VDD supply

range.

The ADC features a hardware oversampler up to 256 samples, improving the resolution to

16 bits (refer to AN2668).

An analog watchdog feature allows very precise monitoring of the converted voltage of one,

some or all scanned channels. An interrupt is generated when the converted voltage is

outside the programmed thresholds.

The events generated by the general-purpose timers (TIMx) can be internally connected to

the ADC start triggers, to allow the application to synchronize A/D conversions with timers.

3.14.1

Temperature sensor

The temperature sensor (TS) generates a voltage VTS that varies linearly with temperature.

The temperature sensor is internally connected to an ADC input to convert the sensor

output voltage into a digital value.

The sensor provides good linearity but it has to be calibrated to obtain good overall

accuracy of the temperature measurement. As the offset of the temperature sensor may

vary from part to part due to process variation, the uncalibrated internal temperature sensor

is suitable only for relative temperature measurements.

To improve the accuracy of the temperature sensor, each part is individually factory-

calibrated by ST. The resulting calibration data are stored in the part’s engineering bytes,

accessible in read-only mode.

Table 5. Temperature sensor calibration values

Calibration value name

Description

Memory address

TS_CAL1

TS ADC raw data acquired at a

temperature of 30 °C (± 5 °C),

VDDA = VREF+ = 3.0 V (± 10 mV)

0x1FFF 75A8 - 0x1FFF 75A9

TS_CAL2

TS ADC raw data acquired at a

temperature of 130 °C (± 5 °C),

VDDA = VREF+ = 3.0 V (± 10 mV)

0x1FFF 75CA - 0x1FFF 75CB

STM32G071C8 データシート(PDF) 25 Page - STMicroelectronics

STM32G071C8 データシート(HTML) 25 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード