AD9913SLASHPCBZ datasheet(23/32 Pages) AD

23 / 32 page

Data Sheet

AD9913

Rev. E | Page 23 of 32

Instruction Byte

The instruction byte contains the following information as

shown in the instruction byte bit map.

Instruction Byte Information Bit Map

MSB

LSB

R/W

R/W—Bit 7 of the instruction byte determines whether a read

or write data transfer occurs after the instruction byte write.

Logic high indicates read operation. Logic 0 indicates a write

operation.

X, X—Bit 6 and Bit 5 of the instruction byte are don’t care.

A4, A3, A2, A1, A0—Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0 of the

instruction byte determine which register is accessed during the

data transfer portion of the communications cycle.

Serial Interface Port Pin Description

SCLK—Serial Port Clock

The serial clock pin is used to synchronize data to and from the

AD9913 and to run the internal state machines.

CS—Chip Select

Active low input that allows more than one device on the same

serial communications line. The SDIO pin goes to a high

impedance state when this input is high. If driven high during

any communications cycle, that cycle is suspended until chip

select is reactivated low. Chip select can be tied low in systems

that maintain control of SCLK.

SDIO—Serial Data I/O.

Data is always written into and read from the AD9913 on

this pin.

MSB/LSB Transfers

The AD9913 serial port can support both most significant bit

(MSB) first or least significant bit (LSB) first data formats. This

functionality is controlled by the CFR1 [23]. The default value

is MSB first. The instruction byte must be written in the format

indicated by Control Register 0x00 Bit 8. That is, if the AD9913

is in LSB first mode, the instruction byte must be written from

least significant bit to most significant bit.

For MSB first operation, the serial port controller generates the

most significant byte (of the specified register) address first

followed by the next less significant byte addresses until the I/O

operation is complete. All data written to (read from) the

AD9913 must be in MSB first order.

If the LSB mode is active, the serial port controller generates the

least significant byte address first followed by the next greater

significant byte addresses until the I/O operation is complete.

All data written to (read from) the AD9913 must be in LSB

first order.

Notes on Serial Port Operation

The LSB first bit resides in CFR1 [23]. Note that the

configuration changes immediately upon writing to the byte

containing the LSB first bit. Therefore, care must be taken to

compensate for this new configuration for the remainder of the

current communication cycle.

Reading profile registers requires that the external profile select

pins (PS[2:0]) be configured to select the corresponding

PARALLEL I/O PROGRAMMING

Parallel Port Interface Pin Description

CS—Chip Select

An active low on this pin indicates that a read/write operation

is about to be performed. If this pin goes high during an access,

the parallel port is reset to its initial condition.

R/W

—Read/Write

A high on Pin 29 combined with CS active low indicates a read

operation. A low on this pin indicates a write operation.

PCLK—Parallel Port Clock

The parallel clock pin is used to synchronize data to and from

the AD9913 and to run the internal state machines.

ADDR/DATA [7:0]

The 8-bit address/data bus. It works in a bidirectional fashion

to support both read and write operations.

Notes on Parallel Port Operation

Each operation works in a 3-PCLK cycle with the first clock

cycle for addressing, the second for reading or writing, and the

third for re-initialization. In parallel port operation, each byte is

programmed individually.

AD9913/PCBZ データシート(PDF) 23 Page - Analog Devices

AD9913/PCBZ データシート(HTML) 23 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

データシートダウンロード