ADR02 datasheet(21/33 Pages) AD

21 / 33 page

Preliminary Technical Data

AD5762R

Rev. PrA | Page 21 of 33

THEORY OF OPERATION

The AD5762R is a dual, 16-bit, serial input, bipolar voltage output

DAC and operates from supply voltages of ±11.4 V to ±16.5 V and

has a buffered output voltage of up to ±10.5263 V. Data is written to

the AD5762R in a 24-bit word format, via a 3-wire serial interface.

The AD5762R also offers an SDO pin, which is available for daisy

chaining or readback.

The AD5762R incorporates a power-on reset circuit, which

ensures that the DAC registers power up loaded with 0x0000.

The AD5762R features a digital I/O port that can be

programmed via the serial interface, an analog die temperature

sensor, on-chip 10 ppm/°C voltage reference, on-chip reference

buffers and per channel digital gain and offset registers.

DAC ARCHITECTURE

The DAC architecture of the AD5762R consists of a 16-bit

current mode segmented R-2R DAC. The simplified circuit

diagram for the DAC section is shown in Figure 38.

The four MSBs of the 16-bit data word are decoded to drive 15

switches, E1 to E15. Each of these switches connects one of the

15 matched resistors to either AGND or IOUT. The remaining

12 bits of the data word drive switches S0 to S11 of the 12-bit R-

2R ladder network.

E15

VREF

E14

S11

S10

12-BIT, R-2R LADDER

4 MSBs DECODED INTO

15 EQUAL SEGMENTS

VOUT

AGND

R/8

IOUT

Figure 38. DAC Ladder Structure

REFERENCE BUFFERS

The AD5762R can operate with either an external or an internal

reference. The reference input has an input range up to 7 V. This

input voltage is then used to provide a buffered positive and

negative reference for the DAC cores. The positive reference is

given by

+ VREF = 2 × VREFIN

While the negative reference to the DAC cores is given by

−VREF = −2 × VREFIN

These positive and negative reference voltages (along with the

gain register values) define the output ranges of the DACs.

SERIAL INTERFACE

The AD5762R is controlled over a versatile 3-wire serial

interface that operates at clock rates of up to 30 MHz and is

compatible with SPI®, QSPI™, MICROWIRE™, and DSP

standards.

Input Shift Register

The input shift register is 24 bits wide. Data is loaded into the

device MSB first as a 24-bit word under the control of a serial

clock input, SCLK. The input register consists of a read/write

bit, three register select bits, three DAC address bits and 16 data

bits as shown in Table 7. The timing diagram for this operation

is shown in Figure 2.

Upon power-up, the DAC registers are loaded with zero code

(0x0000) and the outputs are clamped to 0 V via a low

impedance path. The outputs can be updated with the zero code

value by asserting either LDAC or CLR. The corresponding

output voltage depends on the state of the BIN/2sCOMP pin. If

the BIN/2sCOMP pin is tied to DGND, then the data coding is

twos complement and the outputs update to 0 V. If the

BIN/2sCOMP pin is tied to DVCC, then the data coding is offset

binary and the outputs update to negative full scale. To have the

outputs power-up with zero code loaded to the outputs, the

CLR pin should be held low during power-up.

Standalone Operation

The serial interface works with both a continuous and noncon-

tinuous serial clock. A continuous SCLK source can only be

used if SYNC is held low for the correct number of clock cycles.

In gated clock mode, a burst clock containing the exact number

of clock cycles must be used and SYNC must be taken high after

the final clock to latch the data. The first falling edge of SYNC

starts the write cycle. Exactly 24 falling clock edges must be

applied to SCLK before SYNC is brought back high again. If

SYNC is brought high before the 24

th falling SCLK edge, then

the data written is invalid. If more than 24 falling SCLK edges

are applied before SYNC is brought high, then the input data is

also invalid. The input register addressed is updated on the

rising edge of SYNC. In order for another serial transfer to take

place, SYNC must be brought low again. After the end of the

serial data transfer, data is automatically transferred from the

input shift register to the addressed register.

When the data has been transferred into the chosen register of

the addressed DAC, all DAC registers and outputs can be

updated by taking LDAC low.

ADR02 データシート(PDF) 21 Page - Analog Devices

ADR02 データシート(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

データシートダウンロード