MPC8572ECLPXATLD datasheet(42/140 Pages) FREESCALE

42 / 140 page

MPC8572E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 4

Freescale Semiconductor

Ethernet: Enhanced Three-Speed Ethernet (eTSEC)

Figure 20 provides the AC test load for eTSEC.

Figure 20. eTSEC AC Test Load

Figure 21 shows the RMII receive AC timing diagram.

Figure 21. RMII Receive AC Timing Diagram

8.3

SGMII Interface Electrical Characteristics

Each SGMII port features a 4-wire AC-Coupled serial link from the dedicated SerDes 2 interface of

MPC8572E as shown in Figure 22, where CTX is the external (on board) AC-Coupled capacitor. Each

output pin of the SerDes transmitter differential pair features 50-

Ω output impedance. Each input of the

SerDes receiver differential pair features 50-

Ω on-die termination to SGND_SRDS2 (xcorevss). The

reference circuit of the SerDes transmitter and receiver is shown in Figure 54.

When an eTSEC port is configured to operate in SGMII mode, the parallel interface’s output signals of

this eTSEC port can be left floating. The input signals should be terminated based on the guidelines

described in Section 21.5, “Connection Recommendations,” as long as such termination does not violate

the desired POR configuration requirement on these pins, if applicable.

RXD[1:0], CRS_DV, RX_ER hold time to

TSECn_TX_CLK rising edge

tRMRDX

2.0

—

Note:

1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)

for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive

timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K)

going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input

signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general,

the clock reference symbol representation is based on three letters representing the clock of a particular functional. For

example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used

with the appropriate letter: R (rise) or F (fall).

Table 35. RMII Receive AC Timing Specifications (continued)

At recommended operating conditions with LVDD/TVDD of 2.5/ 3.3 V ± 5%.

Parameter/Condition

Symbol 1

Min

Typ

Max

Unit

Output

Z0 = 50 Ω

LVDD/2

RL = 50 Ω

TSEC

n_TX_CLK

RXD[1:0]

tRMRDX

tRMR

tRMRH

tRMRR

tRMRF

CRS_DV

RX_ER

tRMRDV

Valid Data

MPC8572ECLPXATLD データシート(PDF) 42 Page - Freescale Semiconductor, Inc

MPC8572ECLPXATLD データシート(HTML) 42 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

データシートダウンロード