EM6620WS27 datasheet(9/56 Pages) EMMICRO

9 / 56 page

EM6620

www.emmicroelectronic.com

4.1 Oscillation Detection Circuit

At power on, the voltage regulator starts to follow the supply voltage and triggers the power on reset circuitry,

and thus the system reset. The CPU of the EM6620 remains in the reset state for the ‘CPU Reset Delay’, to

allow the oscillator to stabilize after power up.

The oscillator is disabled during sleep mode. So when waking up from sleep mode, the CPU of the EM6620

remains in the reset state for the ‘CPU Reset Delay’ , to allow the oscillator to stabilize. During this oscillator

stabilization period, the oscillation detection circuit is inhibited.

In active or standby modes, the oscillator detection circuit monitors the oscillator. If it stops for any reason, a

system reset is generated. After clock restart, the CPU waits for the CPU Reset Delay before executing the first

instructions.

The oscillation detection circuitry can be inhibited with NoOscWD = 1 in register RegVLDCntl. At power up,

and after any Reset, the function is activated.

The ‘CPU Reset Delay’ is 32768 system clocks ( ck[16] ) long.

4.2 Input Port A Reset

By writing the OptInpRSel1 and OptInpRSel2 registers it is possible to choose any combination of port A input

values to execute a system reset. The reset condition must be valid for at least 16 ms (system clock = 32 KHz)

in active and standby mode. The applied port A reset condition will immediately trigger a system reset in Sleep

mode.

Bit NoInputReset in option register OptFSelPB selects the input port A reset function in active and standby

mode. If set to "0" the occurrence of the selected combination for input port A reset will trigger a system reset.

Set to ‘1’ the input port A reset function is inhibited.

This option bit has no action in sleep mode, where the occurrence of the selected input port A reset

combination will always immediately trigger a system reset.

Reset combination selection (InpReset) in registers OptInpRSel1 and OptInpRSel2.

InpReset = InpResPA[0] • InpResPA[1] • InpResPA[2] • InpResPA[3]

InpRes1PA[n] InpRes2PA[n] InpResPA[n]

VSS

PA[n]

not PA[n]

VDD

n = 0 to 3

i.e. ; - No reset if InpResPA[n] = VSS.

- Don't care function on a single bit with

its InpResPA[n] = VDD.

- Always Reset if InpResPA[3:0] = 'b1111.

Figure 7. Input port A reset structure

MUX

VSS

PA[3]

VDD

BIT

[0]

BIT

[1]

BIT

[2]

BIT

[3]

InpResPA

InpResPA[3]

InpRes2PA[3]

InpRes1PA[3]

Input PortA Reset

Bit[2] selection

Input PortA Reset

Bit[1] selection

Input PortA Reset

Bit[0] selection

Input PortA Reset

Bit[3] selection

Input

Reset

from

PortA

EM6620WS27 データシート(PDF) 9 Page - EM Microelectronic - MARIN SA

EM6620WS27 データシート(HTML) 9 Page - EM Microelectronic - MARIN SA

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

データシートダウンロード

リンク URL

EM6620WS27 データシート(PDF) 9 Page - EM Microelectronic - MARIN SA

EM6620WS27 データシート(HTML) 9 Page - EM Microelectronic - MARIN SA

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

データシート ダウンロード

リンク URL

データシートダウンロード