EM6620WS27 datasheet(24/56 Pages) EMMICRO

24 / 56 page

EM6620

www.emmicroelectronic.com

For instance, loading the counter in up count mode with hex 000 and the comparator with hex C52 which will

be identified as :

- bits[11:10] are limiting the counter to limits to 4 bits length, =03

(BitSel[1,0])

- bits

[9:4] are the unused counter bits = hex 05 (bin 000101),

(number of PWM pulses)

- bits

[3:0] (comparator value = 2).

(length of PWM pulse)

Thus after 5 PWM-pulses of 2 clocks cycles length the Counter generates an IRQComp and stops.

The same example with SelIntFull=0 (limited bit compare) will produce an unlimited number of PWM at a length

of 2 clock cycles.

7.5.1 How the PWM Generator works.

For Up Count Mode; Setting the counter in up count and PWM mode the PB[3] PWM output is defined to be 0

(EnComp=0 forces the PWM output to 0 in upcount mode, 1 in downcount). Each Roll Over will set the output

to ‘1’ and each Compare Match will set it back to ‘0’. The Compare Match for PWM always only works on the

defined counter length. This, independent of the SelIntFull setting which is valid only for the IRQ generation.

Refer also to the compare setup in chapter 7.4.

In above example the PWM starts counting up on hex 0,

2 cycles later compare match -> PWM to ‘0’,

14 cycles later roll over -> PWM to ‘1’

2 cycles later compare match -> PWM to ‘0’ , etc. until the completion of the 5 pulses.

The normal IRQ generation remains on during PWM output. If no IRQ’s are wanted, the corresponding masks

need to be set.

In Down Count Mode

everything is inverted. The

PWM output starts with the ‘1’ value. Each Roll Over will set the output to ‘0’ and each Compare Match will set

it back to ‘1’. For limited pulse generation one must load the complementary pulse number value. I.e. for 5

pulses counting on 4 bits load bits[9 :4] with hex 3A (bin 111010).

7.5.2 PWM Characteristics

PWM resolution is

: 10bits (1024 steps), 8bits (256 steps), 6bits (64 steps) or 4 bits (16 steps)

the minimal signal period is

: 16 (4-bit) x Fmax*

-> 16 x 1/Ck[15]

-> 977 µs

(32 KHz)

the maximum signal period is

: 1024 x Fmin*

-> 1024 x 1/Ck[1]

-> 1024 s

(32 KHz)

the minimal pulse width is

: 1 bit

-> 1 x 1/Ck[15]

-> 61 µs

(32 KHz)

* This values are for Fmax or Fmin derived from the internal system clock (32kHz). Much shorter (and longer)

PWM pulses can be achieved by using the port A as frequency input.

One must not use a compare value of hex 0 in up count mode nor a value of hex 3FF (or FF,3F, F if limited bit

compare) in downcount mode.

Figure 16. PWM Output in Up Count Mode

Data+2

Data+1

Data-1

Data

...

001

000

03F

03E

PWM output

IRQComp

IRQCount0

Compare

Roll-over

Count[9 :0]

Clock

Figure 17. PWM Output in Down Count Mode

Data-2

Data-1

Data+1

Data

...

3FE

3FF

000

001

PWM output

IRQComp

IRQCount0

Compare

Roll-over

Count[9 :0]

Clock

EM6620WS27 データシート(PDF) 24 Page - EM Microelectronic - MARIN SA

EM6620WS27 データシート(HTML) 24 Page - EM Microelectronic - MARIN SA

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

データシートダウンロード

リンク URL

EM6620WS27 データシート(PDF) 24 Page - EM Microelectronic - MARIN SA

EM6620WS27 データシート(HTML) 24 Page - EM Microelectronic - MARIN SA

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

データシート ダウンロード

リンク URL

データシートダウンロード